Annex II - DETERMINATION OF AIR EMISSION LIMIT VALUES FOR THE CO-INCINERATION OF WASTE

The following formula (mixing rule) is to be applied whenever a specific total emission limit value ‘C’ has not been set out in a table in this Annex.

The limit value for each relevant pollutant and carbon monoxide in the exhaust gas resulting from the co-incineration of waste shall be calculated as follows:

\frac{V_{\mathrm{waste}} \times C_{\mathrm{waste}} + V_{\mathrm{proc}} \times C_{\mathrm{proc}}}{V_{\mathrm{waste}} + V_{\mathrm{proc}1}} = C

Vwaste:

exhaust gas volume resulting from the incineration of waste only determined from the waste with the lowest calorific value specified in the permit and standardised at the conditions given by this Directive.

If the resulting heat release from the incineration of hazardous waste amounts to less than 10 % of the total heat released in the plant, Vwaste must be calculated from a (notional) quantity of waste that, being incinerated, would equal 10 % heat release, the total heat release being fixed.

Cwaste: emission limit values set for incineration plants in Annex V for the relevant pollutants and carbon monoxide.

Vproc: exhaust gas volume resulting from the plant process including the combustion of the authorised fuels normally used in the plant (wastes excluded) determined on the basis of oxygen contents at which the emissions must be standardised as laid down in Community or national regulations. In the absence of regulations for this kind of plant, the real oxygen content in the exhaust gas without being thinned by addition of air unnecessary for the process must be used. The standardisation at the other conditions is given in this Directive.

Cproc: emission limit values as laid down in the tables of this annex for certain industrial sectors or in case of the absence of such a table or such values, emission limit values of the relevant pollutants and carbon monoxide in the flue gas of plants which comply with the national laws, regulations and administrative provisions for such plants while burning the normally authorised fuels (wastes excluded). In the absence of these measures the emission limit values laid down in the permit are used. In the absence of such permit values the real mass concentrations are used.

C: total emission limit values and oxygen content as laid down in the tables of this annex for certain industrial sectors and certain pollutants or in case of the absence of such a table or such values total emission limit values for CO and the relevant pollutants replacing the emission limit values as laid down in specific Annexes of this Directive. The total oxygen content to replace the oxygen content for the standardisation is calculated on the basis of the content above respecting the partial volumes.

Member States may lay down rules governing the exemptions provided for in this Annex.

II.1. Special provisions for cement kilns co-incinerating waste

Daily average values (for continuous measurements) Sample periods and other measurement requirements as in Article 7. All values in mg/m3 (Dioxins and furans ng/m3). Half-hourly average values shall only be needed in view of calculating the daily average values.

The results of the measurements made to verify compliance with the emission limit values shall be standardised at the following conditions: Temperature 273 K, pressure 101,3 kPa, 10 % oxygen, dry gas.

II.1.1. C — total emission limit values

Until 1 January 2008, exemptions for NOx may be authorised by the competent authorities for existing wet process cement kilns or cement kilns which burn less than three tonnes of waste per hour, provided that the permit foresees a total emission limit value for NOx of not more than 1200 mg/m3.

Until 1 January 2008, exemptions for dust may be authorised by the competent authority for cement kilns which burn less than three tonnes of waste per hour, provided that the permit foresees a total emission limit value of not more than 50 mg/m3.

II.1.2. C — total emission limit values for SO2 and TOC

Exemptions may be authorised by the competent authority in cases where TOC and SO2 do not result from the incineration of waste.

II.1.3. Emission limit value for CO

Emission limit values for CO can be set by the competent authority.

II.2. Special provisions for combustion plants co-incinerating waste

II.2.1. Daily average values

Where, for large combustion plants, more stringent emission limit values are set under Directive 2001/80/EC or will be set under other Community legislation, those emission limit values shall replace, for the plants and pollutants concerned, the emission limit values laid down in the following tables (Cproc). In that case, the Commission shall adapt those tables to the more stringent emission limit values. Those measures, designed to amend non-essential elements of this Directive, shall be adopted in accordance with the regulatory procedure with scrutiny referred to in Article 17(2), without delay.

Half-hourly average values shall only be needed in view of calculating the daily average values.

Cproc:

Cproc for solid fuels expressed in mg/Nm3 (O2 content 6 %):

Until 1 January 2007 and without prejudice to relevant Community legislation, the emission limit value for NOx does not apply to plants only co-incinerating hazardous waste.

Until 1 January 2008, exemptions for NOx and SO2 may be authorised by the competent authorities for existing co-incineration plants between 100 and 300 MWth using fluidised bed technology and burning solid fuels provided that the permit foresees a Cproc value of not more than 350 mg/Nm3 for NOx and not more than 850 to 400 mg/Nm3 (linear decrease from 100 to 300 MWth) for SO2.

Cproc for biomass expressed in mg/Nm3 (O2 content 6 %):

‘Biomass’ means: products consisting of any whole or part of a vegetable matter from agriculture or forestry, which can be used for the purpose of recovering its energy content as well as wastes listed in Article 2(2)(a)(i) to (v).

Until 1 January 2008, exemptions for NOx may be authorised by the competent authorities for existing co-incineration plants between 100 and 300 MWth using fluidised bed technology and burning biomass provided that the permit foresees a Cproc value of not more than 350 mg/Nm3.

Cproc for liquid fuels expressed in mg/Nm3 (O2 content 3 %):

II.2.2. C — total emission limit values

C expressed in mg/Nm3 (O2 content 6 %). All average values over the sample period of a minimum of 30 minutes and a maximum of 8 hours:

C expressed in ng/Nm3 (O2 content 6 %). All average values measured over the sample period of a minimum of 6 hours and a maximum of 8 hours:

II.3. Special provisions for industrial sectors not covered under II.1 or II.2 co-incinerating waste

II.3.1. C — total emission limit values:

C expressed in ng/Nm3. All average values measured over the sample period of a minimum of 6 hours and a maximum of 8 hours:

C expressed in mg/Nm3. All average values over the sample period of a minimum of 30 minutes and a maximum of 8 hours: