Designation of the substance, of the groups of substances or of the ►M3 mixture ◄ | Conditions of restriction |
1. Polychlorinated terphenyls (PCTs) — ►M3 Mixtures ◄, including waste oils, with a PCT content higher than 0,005 % by weight. | 1. Shall not be used. However, the following use of equipment, installations and fluids which were in service on 30 June 1986 shall continue to be permitted until they are disposed of or reach the end of their service life: (a) closed-system electrical equipment transformers, resistors and inductors; (b) large condensers (≥ 1 kg total weight); (c) small condensers; (d) heat-transmitting fluids in closed-circuit heat-transfer installations; (e) hydraulic fluids for underground mining equipment. 2. The Member State may, for reasons of protection of human health and the environment, prohibit the use of equipment, installations and fluids covered by paragraph 1 before they are disposed of or reach the end of their service life. 3. The placing on the second-hand market of equipment, plant and fluids covered by paragraph 1 which are not intended for disposal shall be prohibited. 4. Where the Member State considers that it is not possible for technical reasons to use substitute articles, it may permit the use of PCTs and ►M3 mixtures ◄ thereof where the latter are solely intended, in the normal conditions of maintenance of equipment, to supplement the level of liquids containing PCTs in properly functioning existing installations purchased before 1 October 1985. 5. The Member State may, provided prior notification stating the reasons is sent to the Commission, grant derogations from the ban on the placing on the market and use of primary and intermediate substances or ►M3 mixtures ◄, in so far as they consider that these derogations have no deleterious effects on human health and the environment. 6. Without prejudice to the implementation of other Community provisions relating to the labelling of dangerous substances and ►M3 mixtures ◄, equipment and installations containing PCTs must also display instructions concerning the disposal of PCTs and the maintenance and use of equipment and installations containing them. These instructions must be capable of being read horizontally when the object containing the PCTs is installed in the normal way. The inscription must stand out clearly from its background and shall be in a language which is understood in the territory where it is being used. |
2. Chloro-1-ethylene (monomer vinyl chloride) CAS No 75-01-4 EINECS No 200-831-0 | Shall not be used as aerosol propellant for any use. |
3. Liquid substances or ►M3 mixtures ◄, which are regarded as dangerous according to the definitions in Council Directive 67/548/EEC and Directive 1999/45/EC. | 1. Shall not be used in: — ornamental objects, intended to produce light or colour effects by means of different phases, for example in ornamental lamps and ashtrays, — tricks and jokes, — games for one or more participants, or any object intended to be used as such, even with ornamental aspects. 2. Without prejudice to paragraph 1, substances and ►M3 mixtures ◄ which: — present an aspiration hazard and are labelled with R65, and — can be used as fuel in decorative lamps, and — are placed on the market in packaging of a capacity of 15 litres or less, shall not contain a colouring agent, unless required for fiscal reasons, or perfume or both. 3. Without prejudice to the implementation of other Community provisions relating to the classification, packaging and labelling of dangerous substances and ►M3 mixtures ◄, the packaging of substances and ►M3 mixtures ◄ covered by paragraph 2, where intended for use in lamps, must be marked legibly and indelibly as follows: ‘Keep lamps filled with this liquid out of the reach of children’. |
4. Tris (2,3 dibromopropyl) phosphate CAS No 126-72-7 | Shall not be used in textile articles, such as garments, undergarments and linen, intended to come into contact with the skin. |
5. Benzene CAS No 71-43-2 EINECS No 200-753-785 | 1. Not permitted in toys or parts of toys as placed on the market where the concentration of benzene in the free state is in excess of 5 mg/kg of the weight of the toy or part of toy. 2. Shall not be used in concentrations equal to, or greater than, 0,1 % by mass in substances or ►M3 mixtures ◄ placed on the market. 3. However, paragraph 2 shall not apply to: (a) motor fuels which are covered by Directive 98/70/EC; (b) substances and ►M3 mixtures ◄ for use in industrial processes not allowing for the emission of benzene in quantities in excess of those laid down in existing legislation; (c) waste covered by Council Directive 91/689/EEC of 12 December 1991 on hazardous waste (1) and Directive 2006/12/EC. |
6. Asbestos fibres (a) Crocidolite CAS No 12001-28-4 (b) Amosite CAS No 12172-73-5 (c) Anthophyllite CAS No 77536-67-5 (d) Actinolite CAS No 77536-66-4 (e) Tremolite CAS No 77536-68-6 (f) Chrysotile (2) CAS No 12001-29-5 CAS No 132207-32-0 | 1. The placing on the market and use of these fibres and of articles containing these fibres added intentionally shall be prohibited. However, Member States may except the placing on the market and use of diaphragms containing chrysotile (point (f)) for existing electrolysis installations until they reach the end of their service life, or until suitable asbestos-free substitutes become available, whichever is the sooner. The Commission will review this derogation before 1 January 2008. 2. The use of articles containing asbestos fibres referred to in paragraph 1 which were already installed and/or in service before 1 January 2005 shall continue to be permitted until they are disposed of or reach the end of their service life. However, Member States may, for reasons of protection of human health, prohibit the use of such articles before they are disposed of or reach the end of their service life. Member States shall not permit the introduction of new applications for chrysotile asbestos on their territories. 3. Without prejudice to the application of other Community provisions on the classification, packaging and labelling of dangerous substances and ►M3 mixtures ◄, the placing on the market and use of these fibres and of articles containing these fibres, as permitted according to the preceding derogations, shall be permitted only if the articles bear a label in accordance with the provisions of Appendix 7 to this Annex. |
7. Tris(aziridinyl)phosphinoxide CAS No 5455-55-1 | Shall not be used in textile articles, such as garments, undergarments and linen, intended to come into contact with the skin. |
8. Polybromobiphenyls; Polybrominatedbiphenyls (PBB) CAS No 59536-65-1 | |
9. Soap bark powder (Quillaja saponaria) and its derivatives containing saponines Powder of the roots of Helleborus viridis and Helleborus niger Powder of the roots of Veratrum album and Veratrum nigrum Benzidine and/or its derivatives CAS No 92-87-5 EINECS No 202-199-1 o-Nitrobenzaldehyde CAS No 552-89-6 Wood powder | 1. Shall not be used in jokes and hoaxes or in objects intended to be used as such, for instance as a constituent of sneezing powder and stink bombs. 2. However, paragraph 1 does not apply to stink bombs containing not more than 1,5 ml of liquid. |
10. Ammonium sulphide CAS No 12135-76-1 Ammonium hydrogen sulphide CAS No 12124-99-1 Ammonium polysulphide CAS No 9080-17-5 EINECS No 232-989-1 | |
11. Volatile esters of bromoacetic acids: Methyl bromoacetate CAS No 96-32-2 EINECS No 202-499-2 Ethyl bromoacetate CAS No 105-36-2 EINECS No 203-290-9 Propyl bromoacetate CAS No 35223-80-4 Butyl bromoacetate | |
12. 2-Naphthylamine CAS No 91-59-8 EINECS No 202-080-4 and its salts 13. Benzidine CAS No 92-87-5 EINECS No 202-199-1 and its salts 14. 4-Nitrobiphenyl CAS No 92-93-3 EINECS No 202-204-7 15. 4-Aminobiphenyl xenylamine CAS No 92-67-1 EINECS No 202-177-1 and its salts | 1. Shall not be used in concentrations equal to or greater than 0,1 % by weight in substances and ►M3 mixtures ◄ placed on the market. However, this provision shall not apply to waste containing one or more of these substances and covered by Directives 91/689/EEC and 2006/12/EC. 2. Such substances and ►M3 mixtures ◄ shall not be sold to the general public. 3 Without prejudice to the application of other Community provisions on the classification, packaging and labelling of dangerous substances and ►M3 mixtures ◄, the packaging of such ►M3 mixtures ◄ shall be legible and indelibly marked as follows: ‘Restricted to professional users’. |
16. Lead carbons: (a) Neutral anhydrous carbonate (PbCO3) CAS No 598-63-0 EINECS No 209-943-4 (b) Trilead-bis(carbonate)-dihydroxide 2 Pb CO3-Pb(OH)2 CAS No 1319-46-6 EINECS No 215-290-6 | Shall not be used as substances and a constituent of ►M3 mixtures ◄ intended for use as paints, except for the restoration and maintenance of works of art and historic buildings and their interiors, where Member States wish to permit this on their territory, in accordance with the provisions of ILO Convention 13 on the use of white lead and sulphates of lead in paint. |
17. Lead sulphates (a) PbSO4 (1:1) CAS No 7446-14-2 EINECS No 231-198-9 (b) Pbx SO4 CAS No 15739-80-7 EINECS No 239-831-0 | |
18. Mercury compounds | 1. Shall not be used as substances and constituents of ►M3 mixtures ◄ intended for use: (a) to prevent the fouling by micro-organisms, plants or animals of: — the hulls of boats, — cages, floats, nets and any other appliances or equipment used for fish or shellfish farming, — any totally or partly submerged appliances or equipment; (b) in the preservation of wood; (c) in the impregnation of heavy-duty industrial textiles and yarn intended for their manufacture; (d) in the treatment of industrial waters, irrespective of their use. 2. The placing on the market of batteries and accumulators, containing more than 0,0005 % of mercury by weight, including in those cases where these batteries and accumulators are incorporated into appliances shall be prohibited. Button cells and batteries composed of button cells with a mercury content of no more than 2 % by weight shall be exempted from this prohibition. |
19. Arsenic compounds | 1. Shall not be used as substances and constituents of ►M3 mixtures ◄ intended for use: (a) to prevent the fouling by micro-organisms, plants or animals of: — the hulls of boats, — cages, floats, nets and any other appliances or equipment used for fish or shellfish farming, — any totally or partly submerged appliances or equipment; (b) in the preservation of wood. Furthermore, wood so treated shall not be placed on the market; (c) however, by way of derogation: (i) Relating to the substances and ►M3 mixtures ◄ in the preservation of wood: these may only be used in industrial installations using vacuum or pressure to impregnate wood if they are solutions of inorganic compounds of the copper, chromium, arsenic (CCA) type C. Wood so treated shall not be placed on the market before fixation of the preservative is completed. (ii) Relating to wood treated with CCA solutions in industrial installations according to point (i): this may be placed on the market for professional and industrial use provided that the structural integrity of the wood is required for human or livestock safety and skin contact by the general public during its service life is unlikely: — as structural timber in public and agricultural buildings, office buildings, and industrial premises, — in bridges and bridgework, — as constructional timber in freshwater areas and brackish waters e.g. jetties and bridges, — as noise barriers, — in avalanche control, — in highway safety fencing and barriers, — as debarked round conifer livestock fence posts, — in earth retaining structures, — as electric power transmission and telecommunications poles, — as underground railway sleepers. Without prejudice to the application of other Community provisions on the classification, packaging and labelling of dangerous substances and ►M3 mixtures ◄, all treated wood placed on the market shall be individually labelled ‘For professional and industrial installation and use only, contains arsenic’. In addition, all wood placed on the market in packs shall also bear a label stating ‘Wear gloves when handling this wood. Wear a dust mask and eye protection when cutting or otherwise crafting this wood. Waste from this wood shall be treated as hazardous by an authorised undertaking’. (iii) Treated wood referred to under points (i) and (ii) shall not be used: — in residential or domestic constructions, whatever the purpose, — in any application where there is a risk of repeated skin contact, — in marine waters, — for agricultural purposes other than for livestock fence posts and structural uses in accordance with point (ii), — in any application where the treated wood may come into contact with intermediate or finished products intended for human and/or animal consumption. 2. Shall not be used as substances and constituents of ►M3 mixtures ◄ intended for use in the treatment of industrial waters, irrespective of their use. |
20. Organostannic compounds | 1. Shall not be placed on the market for use as substances and constituents of ►M3 mixtures ◄ when acting as biocides in free association paint. 2. Shall not be placed on the market or used as substances and constituents of ►M3 mixtures ◄ which act as biocides to prevent the fouling by micro-organisms, plants or animals of: (a) all craft irrespective of their length intended for use in marine, coastal, estuarine and inland waterways and lakes; (b) cages, floats, nets and any other appliances or equipment used for fish or shellfish farming; (c) any totally or partly submerged appliance or equipment. 3. Shall not be used as substances and constituents of ►M3 mixtures ◄ intended for use in the treatment of industrial waters. |
21. Di-μ-oxo-di-n-butylstanniohydroxyborane dibutyltin hydrogen borate C8H19BO3Sn (DBB) CAS No 75113-37-0 ELINCS No 401-040-5 | Shall be prohibited in a concentration equal to or greater than 0,1 % in substances and constituents of ►M3 mixtures ◄ placed on the market. However, this provision shall not apply to this substance (DBB) or ►M3 mixtures ◄ containing it if these are intended solely for conversion into finished articles, among which this substance will no longer feature in a concentration equal to or greater than 0,1 %. |
22. Pentachlorophenol CAS No 87-86-5 EINECS No 201-778-6 and its salts and esters | 1. Shall not be used in a concentration equal to or greater than 0,1 % by mass in substances or ►M3 mixtures ◄ placed on the market. 2. Transitional provisions: By way of derogation until 31 December 2008 France, Ireland, Portugal, Spain and the United Kingdom may chose not to apply this provision to substances and ►M3 mixtures ◄ intended for use in industrial installations not permitting the emission and/or discharge of pentachlorophenol (PCP) in quantities greater than those prescribed by existing legislation: (a) in the treatment of wood. However, treated wood shall not be used: — inside buildings whether for decorative purposes or not, whatever their purpose (residence, employment, leisure), — for the manufacture and re-treatment of: — (i) containers intended for growing purposes; (ii) packaging that may come into contact with raw materials, intermediate or finished products destined for human and/or animal consumption; (iii) other materials that may contaminate the products mentioned in (i) and (ii); (b) in the impregnation of fibres and heavy-duty textiles not intended in any case for clothing or for decorative furnishings; (c) by way of special exception, Member States may on a case-by-case basis, permit on their territory specialised professionals to carry out in situ and for buildings of cultural, artistic and historical interest, or in emergencies, a remedial treatment of timber and masonry infected by dry rot fungus (Serpula lacrymans) and cubic rot fungi. In any case: (a) Pentachlorophenol used alone or as a component of ►M3 mixtures ◄ employed within the framework of the above exceptions must have a total hexachlorodibenzoparadioxin (HCDD) content of not more than two parts per million (ppm); (b) these substances and ►M3 mixtures ◄ shall not: — be placed on the market except in packages of 20 litres or more; — be sold to the general public. 3. Without prejudice to the implementation of other Community provisions concerning the classification, packaging and labelling of dangerous substances and ►M3 mixtures ◄, the packaging of substances and ►M3 mixtures ◄ covered by paragraphs 1 and 2 shall be marked clearly and indelibly: ‘Reserved for industrial and professional use’. This provision shall not apply to waste covered by Directives 91/689/EEC and 2006/12/EC. |
23. Cadmium CAS No 7440-43-9 EINECS No 231-152-8 and its compounds | 1. Shall not be used to give colour to finished articles manufactured from the substances and ►M3 mixtures ◄ listed below: (a) — polyvinyl chloride (PVC) [3904 10] [3904 21] [3904 22] (3), — polyurethane (PUR) [3909 50] (3), — low-density polyethylene (ld PE), with the exception of low-density polyethylene used for the production of coloured masterbatch [3901 10] (3), — cellulose acetate (CA) [3912 11] [3912 12] (3), — cellulose acetate butyrate (CAB) [3912 11] [3912 12] (3), — epoxy resins [3907 30] (3), — melamine — formaldehyde (MF) resins [3909 20] (3), — urea — formaldehyde (UF) resins [3909 10] (3), — unsaturated polyesters (UP) [3907 91] (3), — polyethylene terephthalate (PET) [3907 60] (3), — polybutylene terephthalate (PBT) (3), — transparent/general-purpose polystyrene [3903 11] [3903 19] (3), — acrylonitrile methylmethacrylate (AMMA) (3), — cross-linked polyethylene (VPE) (3), — high-impact polystyrene (3), — polypropylene (PP) [3902 10] (3); (b) paints [3208] [3209] (3). However, if the paints have a high zinc content, their residual concentration of cadmium shall be as low as possible and shall at all events not exceed 0,1 % by mass. In any case, whatever their use or intended final purpose, finished articles or components of articles manufactured from the substances and ►M3 mixtures ◄ listed above coloured with cadmium shall not be placed on the market if their cadmium content (expressed as Cd metal) exceeds 0,01 % by mass of the plastic material. 2. However, paragraph 1 does not apply to articles to be coloured for safety reasons. 3. Shall not be used to stabilise the finished articles listed below manufactured from polymers or copolymers of vinyl chloride: — packaging materials (bags, containers, bottles, lids) [3923 29 10] [3920 41] [3920 42] (3), — office or school supplies [3926 10] (3), — fittings for furniture, coachwork or the like [3926 30] (3), — articles of apparel and clothing accessories (including gloves) [3926 20] (3), — floor and wall coverings [3918 10] (3), — impregnated, coated, covered or laminated textile fabrics [5903 10] (3), — imitation leather [4202] (3), — gramophone records [8524 10] (3), — tubes and pipes and their fittings [3917 23] (3), — swing doors (3), — vehicles for road transport (interior, exterior, underbody) (3), — coating of steel sheet used in construction or in industry (3), — insulation for electrical wiring (3). In any case, whatever their use or intended final purpose, the placing on the market of the above finished articles or components of articles manufactured from polymers or copolymers of vinyl chloride, stabilised by substances containing cadmium shall be prohibited, if their cadmium content (expressed as Cd metal) exceeds 0,01 % by mass of the polymer. 4. However, paragraph 3 does not apply to finished articles using cadmium-based stabilisers for safety reasons. 5. Within the meaning of this Regulation, ‘cadmium plating’ means any deposit or coating of metallic cadmium on a metallic surface. Shall not be used for cadmium plating metallic articles or components of the articles used in the sectors/applications listed below: (a) equipment and machinery for: — food production [8210] [8417 20] [8419 81] [8421 11] [8421 22] [8422] [8435] [8437] [8438] [8476 11] (3), — agriculture [8419 31] [8424 81] [8432] [8433] [8434] [8436] (3), — cooling and freezing [8418] (3), — printing and book-binding [8440] [8442] [8443] (3); (b) equipment and machinery for the production of: — household goods [7321] [8421 12] [8450] [8509] [8516] (3), — furniture [8465] [8466] [9401] [9402] [9403] [9404] (3), — sanitary ware [7324] (3), — central heating and air conditioning plant [7322] [8403] [8404] [8415] (3). In any case, whatever their use or intended final purpose, the placing on the market of cadmium-plated articles or components of such articles used in the sectors/applications listed in points (a) and (b) above and of articles manufactured in the sectors listed in point (b) above shall be prohibited. 6. The provisions referred to in paragraph 5 are also applicable to cadmium-plated articles or components of such articles when used in the sectors/applications listed in points (a) and (b) below and to articles manufactured in the sectors listed in (b) below: (a) equipment and machinery for the production of: — paper and board [8419 32] [8439] [8441] (3), — textiles and clothing [8444] [8445] [8447] [8448] [8449] [8451] [8452] (3); (b) equipment and machinery for the production of: — industrial handling equipment and machinery [8425] [8426] [8427] [8428] [8429] [8430] [8431] (3), — road and agricultural vehicles [chapter 87] (3), — rolling stock [chapter 86] (3), — vessels [chapter 89] (3). 7. However, the restrictions in paragraphs 5 and 6 do not apply to: — articles and components of the articles used in the aeronautical, aerospace, mining, offshore and nuclear sectors whose applications require high safety standards and in safety devices in road and agricultural vehicles, rolling stock and vessels, — electrical contacts in any sector of use, on account of the reliability required of the apparatus on which they are installed. Owing to the development of knowledge and techniques in respect of substitutes less dangerous than cadmium and its compounds, the Commission shall, in consultation with the Member States, assess the situation at regular intervals in accordance with the procedure laid down in Article 133(3) of this Regulation. |
24. Monomethyl — tetrachlorodiphenyl methane Trade name: Ugilec 141 CAS No 76253-60-6 | 1. The placing on the market and use of this substance and of ►M3 mixtures ◄ and articles containing it shall be prohibited. 2. By way of exception paragraph 1 shall not apply: (a) in the case of plant and machinery already in service on 18 June 1994 until such plant and machinery is disposed of. However, Member States may, on grounds of human health protection and environmental protection, prohibit within their territory the use of such plant or machinery before it is disposed of; (b) in the case of the maintenance of plant and machinery already in service within a Member State on 18 June 1994. 3. The placing on the second-hand market of this substance, ►M3 mixtures ◄ containing this substance and plant/machinery containing this substance, shall be prohibited. |
25. Monomethyl-dichloro-diphenyl methane Trade name: Ugilec 121, Ugilec 21; CAS No — unknown | The placing on the market and use of this substance and of ►M3 mixtures ◄ and articles containing it shall be prohibited. |
26. Monomethyl-dibromo-diphenyl methane bromobenzylbromotoluene, mixture of isomers Trade name: DBBT CAS No 99688-47-8 | The placing on the market and use of this substance and of ►M3 mixtures ◄ and articles containing it shall be prohibited. |
27. Nickel CAS No 7440-02-0 EINECS No 231-111-4 and its compounds | 1. Shall not be used: (a) in all post assemblies which are inserted into pierced ears and other pierced parts of the human body unless the rate of nickel release from such post assemblies is less than 0,2 μg/cm2/week (migration limit); (b) in articles intended to come into direct and prolonged contact with the skin such as: — earrings, — necklaces, bracelets and chains, anklets, finger rings, — wrist-watch cases, watch straps and tighteners, — rivet buttons, tighteners, rivets, zippers and metal marks, when these are used in garments, — if the rate of nickel release from the parts of these articles coming into direct and prolonged contact with the skin is greater than 0,5 μg/cm2/week; (c) in articles such as those listed in point (b) where these have a non-nickel coating unless such coating is sufficient to ensure that the rate of nickel release from those parts of such articles coming into direct and prolonged contact with the skin will not exceed 0,5 μg/cm2/week for a period of at least two years of normal use of the article. 2. Articles which are the subject of paragraph 1, shall not be placed on the market unless they conform to the requirements set out in those points. 3. The standards adopted by the European Committee for Standardisation (CEN) shall be used as the test methods for demonstrating the conformity of articles to paragraphs 1 and 2. |
►M3 28. Substances which appear in Part 3 of Annex VI to Regulation (EC) No 1272/2008 classified as carcinogen category 1A or 1B (Table 3.1) or carcinogen category 1 or 2 (Table 3.2) and listed as follows: — Carcinogen category 1A (Table 3.1)/carcinogen category 1 (Table 3.2) listed in Appendix 1 — Carcinogen category 1B (Table 3.1)/carcinogen category 2 (Table 3.2) listed in Appendix 2 ◄ | Without prejudice to the other parts of this Annex the following shall apply to entries 28 to 30: 1. Shall not be used in substances and ►M3 mixtures ◄ placed on the market for sale to the general public in individual concentration equal to or greater than: ►M3 — either the relevant specific concentration limit specified in Part 3 of Annex VI to Regulation (EC) No 1272/2008, or ◄ — the relevant concentration specified in Directive 1999/45/EC. |
►M3 29. Substances which appear in Part 3 of Annex VI to Regulation (EC) No 1272/2008 classified as germ cell mutagen category 1A or 1B (Table 3.1) or mutagen category 1 or 2 (Table 3.2) and listed as follows: — Mutagen category 1A (Table 3.1)/mutagen category 1 (Table 3.2) listed in Appendix 3 — Mutagen category 1B (Table 3.1)/mutagen category 2 (Table 3.2) listed in Appendix 4 ◄ | Without prejudice to the implementation of other Community provisions relating to the classification, packaging and labelling of dangerous substances and ►M3 mixtures ◄, the packaging of such substances and ►M3 mixtures ◄ must be marked legibly and indelibly as follows: ‘Restricted to professional users’. |
►M3 30. Substances which appear in Part 3 of Annex VI to Regulation (EC) No 1272/2008 classified as toxic to reproduction category 1A or 1B (Table 3.1) or toxic to reproduction category 1 or 2 (Table 3.2) and listed as follows: — Reproductive toxicant category 1A adverse effects on sexual function and fertility or on development (Table 3.1) or reproductive toxicant category 1 with R60 (May impair fertility) or R61 (May cause harm to the unborn child) (Table 3.2) listed in Appendix 5 — Reproductive toxicant category 1B adverse effects on sexual function and fertility or on development (Table 3.1) or reproductive toxicant category 2 with R60 (May impair fertility) or R61 (May cause harm to the unborn child) (Table 3.2) listed in Appendix 6 ◄ | 2. By way of derogation, paragraph 1 shall not apply to: (a) medicinal or veterinary products as defined by Directive 2001/82/EC and Directive 2001/83/EC; (b) cosmetic products as defined by Council Directive 76/768/EEC; (c) — motor fuels which are covered by Directive 98/70/EC, — mineral oil products intended for use as fuel in mobile or fixed combustion plants, — fuels sold in closed systems (e.g. liquid gas bottles); (d) artists' paints covered by Directive 1999/45/EC. |
31. (a) creosote; wash oil CAS No 8001-58-9 EINECS No 232-287-5 (b) creosote oil; wash oil CAS No 61789-28-4 EINECS No 263-047-8 (c) distillates (coal tar), naphthalene oils; naphthalene oil CAS No 84650-04-4 EINECS No 283-484-8 (d) creosote oil, acenaphthene fraction; wash oil CAS No 90640-84-9 EINECS No 292-605-3 (e) distillates (coal tar), upper; heavy anthracene oil CAS No 65996-91-0 EINECS No 266-026-1 (f) anthracene oil CAS No 90640-80-5 EINECS No 292-602-7 (g) tar acids, coal, crude; crude phenols CAS No 65996-85-2 EINECS No 266-019-3 (h) creosote, wood CAS No 8021-39-4 EINECS No 232-419-1 (i) low temperature tar oil, alkaline; extract residues (coal), low temperature coal tar alkaline CAS No 122384-78-5 EINECS No 310-191-5 | 1. Shall not be used as substances or in ►M3 mixtures ◄ in the treatment of wood. Furthermore, wood so treated shall not be placed on the market. 2. However by way of derogation: (a) relating to the substances and ►M3 mixtures ◄: these may be used for wood treatment in industrial installations or by professionals covered by Community legislation on the protection of workers for in situ retreatment only if they contain: (i) benzo[a]pyrene at a concentration of less than 0,005 % by mass; (ii) and water extractable phenols at a concentration of less than 3 % by mass. Such substances and ►M3 mixtures ◄ for use in wood treatment in industrial installations or by professionals: — may be placed on the market only in packaging of a capacity equal to or greater than 20 litres, — shall not be sold to consumers. Without prejudice to the application of other Community provisions on the classification, packaging and labelling of dangerous substances and ►M3 mixtures ◄, the packaging of such substances and ►M3 mixtures ◄ shall be legibly and indelibly marked as follows: ‘For use in industrial installations or professional treatment only’. (b) relating to wood treated in industrial installations or by professionals according to point (a) which is placed on the market for the first time or retreated in situ: this is permitted for professional and industrial use only, e.g. on railways, in electric power transmission and telecommunications, for fencing, for agricultural purposes (e.g. stakes for tree support) and in harbours and waterways; (c) the prohibition in paragraph 1 on the placing on the market shall not apply to wood which has been treated with substances listed in entry 31(a) to (i) before 31 December 2002 and is placed on the second-hand market for re-use. 3. However, treated wood referred to under paragraph 2(b) and (c) shall not be used: — inside buildings, whatever their purpose, — in toys, — in playgrounds, — in parks, gardens, and outdoor recreational and leisure facilities where there is a risk of frequent skin contact, — in the manufacture of garden furniture such as picnic tables, — for the manufacture and use and any re-treatment of: — — containers intended for growing purposes, — packaging that may come into contact with raw materials, intermediate or finished products destined for human and/or animal consumption, — other materials which may contaminate the articles mentioned above. |
32. Chloroform CAS No 67-66-3 EINECS No 200-663-8 33. Carbon tetrachloride-tetrachloromethane CAS No 56-23-5 EINECS No 200-262-8 34. 1,1,2 Trichloroethane CAS No 79-00-5 EINECS No 201-166-9 35. 1,1,2,2 Tetrachloroethane CAS No 79-34-5 EINECS No 201-197-8 36. 1,1,1,2 Tetrachloroethane CAS No 630-20-6 37. Pentachloroethane CAS No 76-01-7 EINECS No 200-925-1 38. 1,1 Dichloroethylene CAS No 75-35-4 EINECS No 200-864-0 39. 1,1,1 Trichloroethane, methyl chloroform CAS No 71-55-6 EINECS No 200-756-3 | 1. Shall not be used in concentrations equal to or greater than 0,1 % by weight in substances and ►M3 mixtures ◄ placed on the market for sale to the general public and/or in diffusive applications such as in surface cleaning and cleaning of fabrics. 2. Without prejudice to the application of other Community provisions on the classification, packaging and labelling of dangerous substances and ►M3 mixtures ◄, the packaging of such substances and ►M3 mixtures ◄ containing them in concentrations equal to or greater than 0,1 % shall be legible and indelibly marked as follows: ‘For use in industrial installations only’. By way of derogation this provision shall not apply to: (a) medicinal or veterinary products as defined by Directive 2001/82/EC and Directive 2001/83/EC; (b) cosmetic products as defined by Directive 76/768/EEC. |
40. Substances meeting the criteria of flammability in Directive 67/548/EEC and classified as flammable, highly flammable or extremely flammable regardless of whether they appear in Annex I to that Directive or not. | 1 Shall not be used on their own or in the form of ►M3 mixtures ◄ in aerosol generators that are placed on the market for the general public for entertainment and decorative purposes such as the following: — metallic glitter intended mainly for decoration, — artificial snow and frost, — ‘whoopee’ cushions, — silly string aerosols, — imitation excrement, — horn for parties, — decorative flakes and foams, — artificial cobwebs, — stink bombs, — etc. 2. Without prejudice to the application of other Community provisions on the classification, packaging and labelling of dangerous substances, the following words must appear legibly and indelibly on the packaging of aerosol generators referred to above: ‘For professional users only’. 3. By way of derogation, paragraphs 1 and 2 shall not apply to the aerosol generators referred to in Article 9a of Council Directive 75/324/EEC of 20 May 1975 on the approximation of the laws of the Member States relating to aerosol dispensers (4). 4. The articles referred to in paragraphs 1 and 2 shall not be placed on the market unless they conform to the requirements indicated. |
41. Hexachloroethane CAS No 67-72-1 EINECS No 200-6664 | Shall not be used in the manufacturing or processing of non-ferrous metals. |
42. Alkanes, C10-C13, chloro (short-chain chlorinated paraffins) (SCCPs) EINECS No 287-476-5 | Shall not be placed on the market for use as substances or as constituents of other substances or ►M3 mixtures ◄ in concentrations higher than 1 %: — in metalworking, — for fat liquoring of leather. |
43. Azocolourants | 1. Azodyes which, by reductive cleavage of one or more azo groups, may release one or more of the aromatic amines listed in Appendix 8, in detectable concentrations, i.e. above 30 ppm in the finished articles or in the dyed parts thereof, according to the testing methods listed in Appendix 10, shall not be used in textile and leather articles which may come into direct and prolonged contact with the human skin or oral cavity, such as: — clothing, bedding, towels, hairpieces, wigs, hats, nappies and other sanitary items, sleeping bags, — footwear, gloves, wristwatch straps, handbags, purses/wallets, briefcases, chair covers, purses worn round the neck, — textile or leather toys and toys which include textile or leather garments, — yarn and fabrics intended for use by the final consumer. 2. Furthermore, the textile and leather articles referred to in paragraph 1 above shall not be placed on the market unless they conform to the requirements set out in that paragraph. 3. Azodyes, which are contained in Appendix 9, ‘List of azodyes’, shall not be placed on the market or used for colouring textile and leather articles as a substance or constituent of ►M3 mixtures ◄ in concentrations higher than 0,1 % by mass. 4. The Commission shall, in the light of new scientific knowledge, review the provisions on azocolourants. |
44. Diphenylether, pentabromo derivative C12H5Br5O | 1. Shall not be placed on the market or used as a substance or as a constituent of ►M3 mixtures ◄ in concentrations higher than 0,1 % by mass. 2. Articles may not be placed on the market if they, or flame-retarded parts thereof, contain this substance in concentrations higher than 0,1 % by mass. |
45. Diphenylether, octabromo derivative C12H2Br8O | 1. Shall not be placed on the market or used as a substance or as a constituent of substances or of ►M3 mixtures ◄ in concentrations higher than 0,1 % by mass. 2. Articles may not be placed on the market if they, or flame-retardant parts thereof, contain this substance in concentrations higher than 0,1 % by mass. |
46. (a) Nonylphenol C6H4(OH)C9H19 (b) Nonylphenol ethoxylate (C2H4O)nC15H24O | Shall not be placed on the market or used as a substance or constituent of ►M3 mixtures ◄ in concentrations equal or higher than 0,1 % by mass for the following purposes: (1) industrial and institutional cleaning except: — controlled closed dry cleaning systems where the washing liquid is recycled or incinerated, — cleaning systems with special treatment where the washing liquid is recycled or incinerated; (2) domestic cleaning; (3) textiles and leather processing except: — processing with no release into waste water, — systems with special treatment where the process water is pre-treated to remove the organic fraction completely prior to biological waste water treatment (degreasing of sheepskin); (4) emulsifier in agricultural teat dips; (5) metal working except: — uses in controlled closed systems where the washing liquid is recycled or incinerated; (6) manufacturing of pulp and paper; (7) cosmetic products; (8) other personal care products except: — spermicides; (9) co-formulants in pesticides and biocides. |
47. Cement | 1. Cement and cement-containing ►M3 mixtures ◄ shall not be used or placed on the market, if they contain, when hydrated, more than 0,0002 % soluble chromium VI of the total dry weight of the cement. 2. If reducing agents are used, then without prejudice to the application of other Community provisions on the classification, packaging and labelling of dangerous substances and ►M3 mixtures ◄, the packaging of cement or cement-containing ►M3 mixtures ◄ shall be legibly and indelibly marked with information on the packing date, as well as on the storage conditions and the storage period appropriate to maintaining the activity of the reducing agent and to keeping the content of soluble chromium VI below the limit indicated in paragraph 1. 3. By way of derogation, paragraphs 1 and 2 shall not apply to the placing on the market for, and use in, controlled closed and totally automated processes in which cement and cement-containing ►M3 mixtures ◄ are handled solely by machines and in which there is no possibility of contact with the skin. |
48. Toluene CAS No 108-88-3 | Shall not be placed on the market or used as a substance or constituent of ►M3 mixtures ◄ in a concentration equal to or higher than 0,1 % by mass in adhesives and spray paints intended for sale to the general public. Member States shall apply these measures from 15 June 2007. |
49. Trichlorobenzene CAS No 120-82-1 | Shall not be placed on the market or used as a substance or constituent of ►M3 mixtures ◄ in a concentration equal to or higher than 0,1 % by mass for all uses except: — as an intermediate of synthesis, or — as a process solvent in closed chemical applications for chlorination reactions, or — in the manufacture of 1,3,5 — trinitro — 2,4,6 — triaminobenzene (TATB). Member States shall apply these measures from 15 June 2007. |
50. Polycyclic-aromatic hydrocarbons (PAH) 1. Benzo(a)pyrene (BaP) CAS No 50-32-8 2. Benzo(e)pyrene (BeP) CAS No 192-97-2 3. Benzo(a)anthracene (BaA) CAS No 56-55-3 4. Chrysen (CHR) CAS No 218-01-9 5. Benzo(b)fluoranthene (BbFA) CAS No 205-99-2 6. Benzo(j)fluoranthene (BjFA) CAS No 205-82-3 7. Benzo(k)fluoranthene (BkFA) CAS No 207-08-9 8. Dibenzo(a, h)anthracene (DBAhA) CAS No 53-70-3 | 1. Extender oils shall not be placed on the market and used for the production of tyres or parts of tyres, if they contain: — more than 1 mg/kg BaP, or — more than 10 mg/kg of the sum of all listed PAHs. These limits are regarded as kept, if the polycyclic aromatics (PCA) extract is less than 3 % by mass, as measured by the Institute of Petroleum standard IP346: 1998 (Determination of PCA in unused lubricating base oils and asphaltene free petroleum fractions — Dimethyl sulphoxide extraction refractive index method), provided that compliance with the limit values of BaP and of the listed PAHs, as well as the correlation of the measured values with the PCA extract, is controlled by the manufacturer or importer every six months or after each major operational change, whichever is earlier. 2. Furthermore, the tyres and treads for retreading manufactured after 1 January 2010 may not be placed on the market if they contain extender oils exceeding the limits indicated in paragraph 1. These limits are regarded as kept, if the vulcanised rubber compounds do not exceed the limit of 0,35 % Bay protons as measured and calculated by ISO 21461 (Rubber vulcanised — Determination of aromaticity of oil in vulcanised rubber compounds). 3. By way of derogation, paragraph 2 shall not apply to retreaded tyres if their tread does not contain extender oils exceeding the limits referred to in paragraph 1. 4. Member States shall apply these measures from 1 January 2010. |
51. The following phthalates (or other CAS- and EINECS numbers covering the substance): bis (2-ethylhexyl) phthalate (DEHP) CAS No 117-81-7 Einecs No 204-211-0 dibutyl phthalate (DBP) CAS No 84-74-2 Einecs No 201-557-4 benzyl butyl phthalate (BBP) CAS No 85-68-7 Einecs No 201-622-7 | Shall not be used as substances or as constituents of ►M3 mixtures ◄, at concentrations higher than 0,1 % by mass of the plasticised material, in toys and childcare articles (5). Toys and childcare articles containing these phthalates in a concentration higher than 0,1 % by mass of the plasticised material shall not be placed on the market. The Commission shall re-evaluate, by 16 January 2010, the measures provided for in relation to this point in the light of new scientific information on such substances and their substitutes, and if justified, these measures shall be modified accordingly. |
52. The following phthalates (or other CAS- and EINECS numbers covering the substance): di-‘isononyl’ phthalate (DINP) CAS No 28553-12-0 and 68515-48-0 Einecs No 249-079-5 and 271-090-9 di-‘isodecyl’ phthalate (DIDP) CAS No 26761-40-0 and 68515-49-1 Einecs No 247-977-1 and 271-091-4 di-n-octyl phthalate (DNOP) CAS No 117-84-0 Einecs No 204-214-7 | Shall not be used as substances or as constituents of ►M3 mixtures ◄, at concentrations higher than 0,1 % by mass of the plasticised material, in toys and childcare articles (5) which can be placed in the mouth by children. Toys and childcare articles containing these phthalates in a concentration higher than 0,1 % by mass of the plasticised material shall not be placed on the market. The Commission shall re-evaluate, by 16 January 2010, the measures provided for in relation to this point in the light of new scientific information on such substances and their substitutes, and if justified, these measures shall be modified accordingly. |
(1) OJ L 377, 31.12.1991, p. 20. Directive as last amended by Regulation (EC) No 166/2006 of the European Parliament and of the Council (OJ L 33, 4.2.2006, p. 1). (2) Chrysotile has two CAS Nos, confirmed by ECB. (3) Council Regulation (EEC) No 2658/87 of 23 July 1987 on the tariff and statistical nomenclature and on the Common Customs Tariff (OJ L 256, 7.9.1987). Regulation as last amended by Regulation (EC) No 426/2006 (OJ L 79, 16.3.2006, p. 1). (4) OJ L 147, 9.6.1975, p. 40. Directive as last amended by Regulation (EC) No 807/2003 (OJ L 122, 16.5.2003, p. 36). (5) For the purposes of this point ‘childcare article’ shall mean any product intended to facilitate sleep, relaxation, hygiene, the feeding of children or sucking on the part of children. | |
Appendices 1 to 6
FOREWORD
Explanations of column headings
Substances:
The name is the same as that used for the substance in ►M3 Part 3 of Annex VI to Regulation (EC) No 1272/2008 ◄. Whenever possible dangerous substances are designated by their EINECS (European Inventory of Existing Commercial Chemical Substances) or ELINCS (European List of Notified Chemical Substances) names. These are referred to as EC numbers in the table. Other entries not listed in EINECS or ELINCS are designated using an internationally recognised chemical name (e.g. ISO, IUPAC). An additional common name is included in some cases.
Index number:
The index number is the identification code given to the substance in ►M3 Part 3 of Annex VI to Regulation (EC) No 1272/2008 ◄. Substances are listed in the Appendix according to this index number.
EINECS number:
For each substance listed in the EINECS there is an identification code. The code starts at 200-001 8.
ELINCS number
For each new substance notified under the Directive 67/548/EEC an identification code has been defined and published in the ELINCS. The code starts at 400-010-9.
CAS number:
Chemical Abstracts Service (CAS) numbers have been defined for substances to help in their identification.
Notes:
The full text of the notes can be found in ►M3 Part 1 of Annex VI to Regulation (EC) No 1272/2008 ◄.
The notes to be taken into account for the purposes of this Regulation are the following:
Note A:
Without prejudice to Article 17(2) of Regulation (EC) No 1272/2008, the name of the substance must appear on the label in the form of one of the designations given in Part 3 of Annex VI to that Regulation.
In that Part, use is sometimes made of a general description such as ‘... compounds’ or ‘... salts’. In this case, the supplier who places such a substance on the market is required to state on the label the correct name, due account being taken of Section 1.1.1.4 of Annex VI to Regulation (EC) No 1272/2008.
In accordance with Regulation (EC) No 1272/2008, where a substance is included in Part 3 of Annex VI to that Regulation, the labelling elements relevant for each specific classification covered by the entry in that Part shall be included in the label, together with the applicable label elements for any other classification not covered by that entry, and any other applicable label elements in accordance with Article 17 of that Regulation.
For substances belonging to one particular group of substances included in Part 3 of Annex VI to Regulation (EC) No 1272/2008, the labelling elements relevant for each specific classification covered by the entry in that Part shall be included in the label, together with the applicable label elements for any other classification not covered by that entry, and any other applicable label elements in accordance with Article 17 of that Regulation.
For substances belonging to more than one group of substances included in Part 3 of Annex VI to Regulation (EC) No 1272/2008, the labelling elements relevant for each specific classification covered by both entries in that Part shall be included in the label, together with the applicable label elements for any other classification not covered by that entry, and any other applicable label elements in accordance with Article 17 of that Regulation. In cases where two different classifications are given in the two entries for the same hazard class or differentiation, the classification reflecting the more severe classification shall be used.
Note C:
Some organic substances may be marketed either in a specific isomeric form or as a mixture of several isomers.
Note D:
Certain substances which are susceptible to spontaneous polymerisation or decomposition are generally placed on the market in a stabilised form. It is in this form that they are listed in Part 3 of Annex VI to Regulation (EC) No 1272/2008.
However, such substances are sometimes placed on the market in a non-stabilised form. In this case, the supplier who places such a substance on the market must state on the label the name of the substance followed by the words ‘non-stabilised’.
Note H:
The classification and label shown for this substance applies to the hazard or hazards indicated by the hazard statement or hazard statements in combination with the hazard classification shown. The requirements of Article 4 of Regulation (EC) No 1272/2008 on suppliers of this substance apply to all other hazard classes, differentiations and categories.
The final label shall follow the requirements of section 1.2 of Annex I to Regulation (EC) No 1272/2008.
Note J:
The classification as a carcinogen need not apply if it can be shown that the substance contains less than 0,1 % w/w benzene (EINECS No 200-753-7).
Note K:
The classification as a carcinogen or mutagen need not apply if it can be shown that the substance contains less than 0,1 % w/w 1,3-butadiene (Einecs No 203-450-8). If the substance is not classified as a carcinogen or mutagen, at least the precautionary statements (P102-)P210-P403 should apply. This note applies only to certain complex oil-derived substances in Part 3 of Annex VI to Regulation (EC) No 1272/2008.
Note L:
The classification as a carcinogen need not apply if it can be shown that the substance contains less than 3 % DMSO extract as measured by IP 346.
Note M:
The classification as a carcinogen need not apply if it can be shown that the substance contains less than 0,005 % w/w benzo[a]-pyrene (EINECS No 200-028-5).
Note N:
The classification as a carcinogen need not apply if the full refining history is known and it can be shown that the substance from which it is produced is not a carcinogen.
Note P:
The classification as a carcinogen need not apply if it can be shown that the substance contains less than 0,1 % w/w benzene (EINECS No 200-753-7).
Note R:
The classification as a carcinogen need not apply to fibres with a length weighted geometric mean diameter, less two standard errors, greater than 6μm.
Note S:
This substance may not require a label according to Article 17 of Regulation (EC) No 1272/2008 (see section 1.3 of Annex I to that Regulation).
Appendix 1
Point 28 — Carcinogens: category 1A (Table 3.1)/category 1 (Table 3.2)
Substances | Index No | EC No | CAS No | Notes |
Chromium (VI) trioxide | 024-001-00-0 | 215-607-8 | 1333-82-0 | E |
Zinc chromates including zinc potassium chromate | 024-007-00-3 | |||
Nickel monoxide | 028-003-00-2 | 215-215-7 | 1313-99-1 | |
Nickel dioxide | 028-004-00-8 | 234-823-3 | 12035-36-8 | |
Dinickel trioxide | 028-005-00-3 | 215-217-8 | 1314-06-3 | |
Nickel sulphide | 028-006-00-9 | 240-841-2 | 16812-54-7 | |
Nickel subsulphide | 028-007-00-4 | 234-829-6 | 12035-72-2 | |
Diarsenic trioxide; arsenic trioxide | 033-003-00-0 | 215-481-4 | 1327-53-3 | |
Arsenic pentoxide; arsenic oxide | 033-004-00-6 | 215-116-9 | 1303-28-2 | |
Arsenic acid and its salts | 033-005-00-1 | |||
Lead hydrogen arsenate | 082-011-00-0 | 232-064-2 | 7784-40-9 | |
Butane [containing ≥ 0,1 % Butadiene (203-450-8)] [1] | 601-004-01-8 | 203-448-7 [1] | 106-97-8 [1] | C, S |
Isobutane [containing ≥ 0,1 % Butadiene (203-450-8)] [2] | 200-857-2 [2] | 75-28-5 [2] | ||
1,3-Butadiene; buta-1,3-diene | 601-013-00-X | 203-450-8 | 106-99-0 | D |
Benzene | 601-020-00-8 | 200-753-7 | 71-43-2 | E |
Triethyl arsenate | 601-067-00-4 | 427-700-2 | 15606-95-8 | |
Vinyl chloride; chloroethylene | 602-023-00-7 | 200-831-0 | 75-01-4 | |
Bis (chloromethyl) ether | 603-046-00-5 | 208-832-8 | 542-88-1 | |
Chloromethyl methyl ether; chlorodimethyl ether | 603-075-00-3 | 203-480-1 | 107-30-2 | |
2-Naphthylamine; beta-naphthylamine | 612-022-00-3 | 202-080-4 | 91-59-8 | E |
Benzidine; 4,4′-diaminobiphenyl; biphenyl-4,4′-ylenediamine | 612-042-00-2 | 202-199-1 | 92-87-5 | E |
Salts of benzidine | 612-070-00-5 | |||
Salts of 2-naphthylamine | 612-071-00-0 | 209-030-0[1] 210-313-6[2] | 553-00-4[1] 612-52-2[2] | |
Biphenyl-4-ylamine; xenylamine; 4-aminobiphenyl | 612-072-00-6 | 202-177-1 | 92-67-1 | |
Salts of biphenyl-4-ylamine; salts of xenylamine; salts of 4-aminobiphenyl | 612-073-00-1 | |||
Tar, coal; Coal tar (The by-product from the destructive distillation of coal. Almost black semisolid. A complex combination of aromatic hydro-carbons, phenolic compounds, nitrogen bases and thiophene.) | 648-081-00-7 | 232-361-7 | 8007-45-2 | |
Tar, coal, high-temperature; Coal tar (The condensation product obtained by cooling, to approximately ambient temperature, the gas evolved in the high temperature (greater than 700 °C) destructive distillation of coal. A black viscous liquid denser than water. Composed primarily of a complex mixture of condensed ring aromatic hydrocarbons. May contain minor amounts of phenolic compounds and aromatic nitrogen bases.) | 648-082-00-2 | 266-024-0 | 65996-89-6 | |
Tar, coal, low-temperature; Coal oil (The condensation product obtained by cooling, to approximately ambient temperature, the gas evolved in low temperature (less than 700 °C) destructive distillation of coal. A black viscous liquid denser than water. Composed primarily of condensed ring aromatic hydrocarbons, phenolic compounds, aromatic nitrogen bases, and their alkyl derivatives.) | 648-083-00-8 | 266-025-6 | 65996-90-9 | |
Tar brown-coal; (An oil distilled from brown-coal tar. Composed primarily of aliphatic, naphthenic and one- to three-ring aromatic hydrocarbons, their alkyl derivates, heteroaromatics and one- and two-ring phenols boiling in the range of approximately 150 °C to 360 °C.) | 648-145-00-4 | 309-885-0 | 101316-83-0 | |
Tar, brown-coal, low temperature; (A tar obtained from low temperature carbonisation and low temperature gasification of brown coal. Composed primarily of aliphatic, naphthenic and cyclic aromatic hydrocarbons, heteroaromatic hydrocarbons and cyclic phenols.) | 648-146-00-X | 309-886-6 | 101316-84-1 | |
Distillates (petroleum), light paraffinic; Unrefined or mildly refined base oil (A complex combination of hydrocarbons produced by vacuum distillation of the residuum from atmospheric distillation of crude oil. It consists of hydrocarbons having carbon numbers predominantly in the range of C15 through C30 and produces a finished oil with a viscosity of less than 19 10-6 m2.s-1 at 40 °C. It contains a relatively large proportion of saturated aliphatic hydrocarbons normally present in this distillation range of crude oil.) | 649-050-00-0 | 265-051-5 | 64741-50-0 | |
Distillates (petroleum), heavy paraffinic; Unrefined or mildly refined base oil (A complex combination of hydrocarbons produced by vacuum distillation of the residuum from atmospheric distillation of crude oil. It consists of hydrocarbons having carbon numbers predominantly in the range of C20 through C50, and produces a finished oil with a viscosity of at least 19 10-6 m2.s-1 at 40 °C. It contains a relatively large proportion of saturated aliphatic hydrocarbons.) | 649-051-00-6 | 265-052-0 | 64741-51-1 | |
Distillates (petroleum), light naphthenic; Unrefined or mildly refined base oil (A complex combination of hydrocarbons produced by vacuum distillation of the residuum from atmospheric distillation of crude oil. It consists of hydrocarbons having carbon numbers predominantly in the range of C15 through C30, and produces a finished oil with a viscosity of less than 19 10-6 m2.s-1 at 40 °C. It contains relatively few normal paraffins.) | 649-052-00-1 | 265-053-6 | 64741-52-2 | |
Distillates (petroleum), heavy naphthenic; Unrefined or mildly refined base oil (A complex combination of hydrocarbons produced by vacuum distillation of the residuum from atmospheric distillation of crude oil. It consists of hydrocarbons having carbon numbers predominantly in the range of C20 through C50, and produces a finished oil with a viscosity of at least 19 10-6 m2.s-1 at 40 °C. It contains relatively few normal paraffins.) | 649-053-00-7 | 265-054-1 | 64741-53-3 | |
Distillates (petroleum), acid-treated heavy naphthenic; Unrefined or mildly refined base oil (A complex combination of hydrocarbons obtained as a raffinate from a sulfuric acid treating process. It consists of hydrocarbons having carbon numbers predominantly in the range of C20 through C50, and produces a finished oil with a viscosity of at least 19 10-6 m2.s-1 at 40 °C. It contains relatively few normal paraffins.) | 649-054-00-2 | 265-117-3 | 64742-18-3 | |
Distillates (petroleum), acid-treated light naphthenic; Unrefined or mildly refined base oil (A complex combination of hydrocarbons obtained as a raffinate from a sulfuric acid treating process. It consists of hydrocarbons having carbon numbers predominantly in the range of C15 through C30, and produces a finished oil with a viscosity of less than 19 10-6 m2.s-1 at 40 °C. It contains relatively few normal paraffins.) | 649-055-00-8 | 265-118-9 | 64742-19-4 | |
Distillates (petroleum), acid-treated heavy paraffinic; Unrefined or mildly refined base oil (A complex combination of hydrocarbons obtained as a raffinate from a sulfuric acid process. It consists predominantly of saturated hydrocarbons having carbon numbers predominantly in the range of C20 through C50, and produces a finished oil with a viscosity of at least 19 10-6 m2.s-1 at 40 °C.) | 649-056-00-3 | 265-119-4 | 64742-20-7 | |
Distillates (petroleum), acid-treated light paraffinic; Unrefined or mildly refined base oil (A complex combination of hydrocarbons obtained as a raffinate from a sulfuric acid treating process. It consists predominantly of saturated hydrocarbons having carbon numbers predominantly in the range of C15 through C30 and produces a finished oil having a viscosity of less than 19 10-6 m2.s-1 at 40 °C.) | 649-057-00-9 | 265-121-5 | 64742-21-8 | |
Distillates (petroleum), chemically neutralised heavy paraffinic; Unrefined or mildly refined base oil (A complex combination of hydrocarbons obtained from a treating process to remove acidic materials. It consists predominantly of hydrocarbons having carbon numbers predominantly in the range of C20 through C50, and produces a finished oil with a viscosity of at least 19 10-6 m2.s-1 at 40 °C. It contains a relatively large proportion of aliphatic hydrocarbons.) | 649-058-00-4 | 265-127-8 | 64742-27-4 | |
Distillates (petroleum), chemically neutralised light paraffinic; Unrefined or mildly refined base oil (A complex combination of hydrocarbons produced by a treating process to remove acidic materials. It consists of hydrocarbons having carbon numbers predominantly in the range of C15 through C30, and produces a finished oil with a viscosity of less than 19 10-6 m2.s-1 at 40 °C.) | 649-059-00-X | 265-128-3 | 64742-28-5 | |
Distillates (petroleum), chemically neutralised heavy naphthenic; Unrefined or mildly refined base oil (A complex combination of hydrocarbons produced by a treating process to remove acidic materials. It consists of hydrocarbons having carbon numbers predominantly in the range of C20 through C50, and produces a finished oil with a viscosity of at least 19 10-6 m2.s-1 at 40 °C. It contains relatively few normal paraffins.) | 649-060-00-5 | 265-135-1 | 64742-34-3 | |
Distillates (petroleum), chemically neutralised light naphthenic; Unrefined or mildly refined base oil (A complex combination of hydrocarbons produced by a treating process to remove acidic materials. It consists of hydrocarbons having carbon numbers predominantly in the range of C15 through C30, and produces a finished oil with a viscosity of less than 19 10-6 m2.s-1 at 40 °C. It contains relatively few normal paraffins.) | 649-061-00-0 | 265-136-7 | 64742-35-4 | |
Gases (petroleum), catalytic cracked naphtha depropaniser overhead, C3-rich acid-free; Petroleum gas (A complex combination of hydrocarbons obtained from fractionation of catalytic cracked hydrocarbons and treated to remove acidic impurities. It consists of hydrocarbons having carbon numbers in the range of C2 through C4, predominantly C3.) | 649-062-00-6 | 270-755-0 | 68477-73-6 | H, K |
Gases (petroleum), catalytic cracker; Petroleum gas (A complex combination of hydrocarbons produced by the distillation of the products from a catalytic cracking process. It consists predominantly of aliphatic hydrocarbons having carbon numbers predominantly in the range of C1 through C6.) | 649-063-00-1 | 270-756-6 | 68477-74-7 | H, K |
Gases (petroleum), catalytic cracker, C1-5-rich; Petroleum gas (A complex combination of hydrocarbons produced by the distillation of products from a catalytic cracking process. It consists of aliphatic hydrocarbons having carbon numbers in the range of C1 through C6, predominantly C1 through C5.) | 649-064-00-7 | 270-757-1 | 68477-75-8 | H, K |
Gases (petroleum), catalytic polymd. naphtha stabiliser overhead, C2-4-rich; Petroleum gas (A complex combination of hydrocarbons obtained from the fractionation stabilisation of catalytic polymerised naphtha. It consists of aliphatic hydrocarbons having carbon numbers in the range of C2 through C6, predominantly C2 through C4.) | 649-065-00-2 | 270-758-7 | 68477-76-9 | H, K |
Gases (petroleum), catalytic reformer, C1-4-rich; Petroleum gas (A complex combination of hydrocarbons produced by distillation of products from a catalytic reforming process. It consists of hydrocarbons having carbon numbers in the range of C1 through C6, predominantly C1 through C4.) | 649-066-00-8 | 270-760-8 | 68477-79-2 | H, K |
Gases (petroleum), C3-5 olefinic-paraffinic alkylation feed; Petroleum gas (A complex combination of olefinic and paraffinic hydrocarbons having carbon numbers in the range of C3 through C5 which are used as alkylation feed. Ambient temperatures normally exceed the critical temperature of these combinations.) | 649-067-00-3 | 270-765-5 | 68477-83-8 | H, K |
Gases (petroleum), C4-rich; Petroleum gas (A complex combination of hydrocarbons produced by distillation of products from a catalytic fractionation process. It consists of aliphatic hydrocarbons having carbon numbers in the range of C3 through C5, predominantly C4.) | 649-068-00-9 | 270-767-6 | 68477-85-0 | H, K |
Gases (petroleum), deethaniser overheads; Petroleum gas (A complex combination of hydrocarbons produced from distillation of the gas and gasoline fractions from the catalytic cracking process. It contains predominantly ethane and ethylene.) | 649-069-00-4 | 270-768-1 | 68477-86-1 | H, K |
Gases (petroleum), deisobutaniser tower overheads; Petroleum gas (A complex combination of hydrocarbons produced by the atmospheric distillation of a butane-butylene stream. It consists of aliphatic hydrocarbons having carbon numbers predominantly in the range of C3 through C4.) | 649-070-00-X | 270-769-7 | 68477-87-2 | H, K |
Gases (petroleum), depropaniser dry, propene-rich; Petroleum gas (A complex combination of hydrocarbons produced by the distillation of products from the gas and gasoline fractions of a catalytic cracking process. It consists predominantly of propylene with some ethane and propane.) | 649-071-00-5 | 270-772-3 | 68477-90-7 | H, K |
Gases (petroleum), depropaniser overheads; Petroleum gas (A complex combination of hydrocarbons produced by distillation of products from the gas and gasoline fractions of a catalytic cracking process. It consists of aliphatic hydrocarbons having carbon numbers predominantly in the range of C2 through C4.) | 649-072-00-0 | 270-773-9 | 68477-91-8 | H, K |
Gases (petroleum), gas recovery plant depropaniser overheads; Petroleum gas (A complex combination of hydrocarbons obtained by fractionation of miscellaneous hydrocarbon streams. It consists predominantly of hydrocarbons having carbon numbers in the range of C1 through C4, predominantly propane.) | 649-073-00-6 | 270-777-0 | 68477-94-1 | H, K |
Gases (petroleum), Girbatol unit feed; Petroleum gas (A complex combination of hydrocarbons that is used as the feed into the Girbatol unit to remove hydrogen sulfide. It consists of aliphatic hydrocarbons having carbon numbers predominantly in the range of C2 through C4.) | 649-074-00-1 | 270-778-6 | 68477-95-2 | H, K |
Gases (petroleum), isomerised naphtha fractionator, C4-rich, hydrogen sulfide-free; Petroleum gas | 649-075-00-7 | 270-782-8 | 68477-99-6 | H, K |
Tail gas (petroleum), catalytic cracked clarified oil and thermal cracked vacuum residue fractionation reflux drum; Petroleum gas (A complex combination of hydrocarbons obtained from fractionation of catalytic cracked clarified oil and thermal cracked vacuum residue. It consists predominantly of hydrocarbons having carbon numbers predominantly in the range of C1 through C6.) | 649-076-00-2 | 270-802-5 | 68478-21-7 | H, K |
Tail gas (petroleum), catalytic cracked naphtha stabilisation absorber; Petroleum gas (A complex combination of hydrocarbons obtained from the stabilisation of catalytic cracked naphtha. It consists predominantly of hydrocarbons having carbon numbers predominantly in the range of C1 through C6.) | 649-077-00-8 | 270-803-0 | 68478-22-8 | H, K |
Tail gas (petroleum), catalytic cracker, catalytic reformer and hydrodesulphuriser combined fractionater; Petroleum gas (A complex combination of hydrocarbons obtained from the fractionation of products from catalytic cracking, catalytic reforming and hydrodesulphurising processes treated to remove acidic impurities. It consists predominantly of hydrocarbons having carbon numbers predominantly in the range of C1 through C5.) | 649-078-00-3 | 270-804-6 | 68478-24-0 | H, K |
Tail gas (petroleum), catalytic reformed naphtha fractionation stabiliser; Petroleum gas (A complex combination of hydrocarbons obtained from the fractionation stabilisation of catalytic reformed naphtha. It consists predominantly of hydrocarbons having carbon numbers predominantly in the range of C1 through C4.) | 649-079-00-9 | 270-806-7 | 68478-26-2 | H, K |
Tail gas (petroleum), saturate gas plant mixed stream, C4-rich; Petroleum gas (A complex combination of hydrocarbons obtained from the fractionation stabilisation of straight-run naphtha, distillation tail gas and catalytic reformed naphtha stabiliser tail gas. It consists of hydrocarbons having carbon numbers in the range of C3 through C6, predominantly butane and isobutane.) | 649-080-00-4 | 270-813-5 | 68478-32-0 | H, K |
Tail gas (petroleum), saturate gas recovery plant, C1-2-rich; Petroleum gas (A complex combination of hydrocarbons obtained from fractionation of distillate tail gas, straight-run naphtha, catalytic reformed naphtha stabiliser tail gas. It consists predominantly of hydrocarbons having carbon numbers in the range of C1 through C5, predominantly methane and ethane.) | 649-081-00-X | 270-814-0 | 68478-33-1 | H, K |
Tail gas (petroleum), vacuum residues thermal cracker; Petroleum gas (A complex combination of hydrocarbons obtained from the thermal cracking of vacuum residues. It consists of hydrocarbons having carbon numbers predominantly in the range of C1 through C5.) | 649-082-00-5 | 270-815-6 | 68478-34-2 | H, K |
Hydrocarbons, C3-4-rich, petroleum distillate; Petroleum gas (A complex combination of hydrocarbons produced by distillation and condensation of crude oil. It consists of hydrocarbons having carbon numbers in the range of C3 through C5, predominantly C3 through C4.) | 649-083-00-0 | 270-990-9 | 68512-91-4 | H, K |
Gases (petroleum), full-range straight-run naphtha dehexaniser off; Petroleum gas (A complex combination of hydrocarbons obtained by the fractionation of the full-range straight-run naphtha. It consists of hydrocarbons having carbon numbers predominantly in the range of C2 through C6.) | 649-084-00-6 | 271-000-8 | 68513-15-5 | H, K |
Gases (petroleum), hydrocracking depropaniser off, hydrocarbon-rich; Petroleum gas (A complex combination of hydrocarbon produced by the distillation of products from a hydrocracking process. It consists predominantly of hydrocarbons having carbon numbers predominantly in the range of C1 through C4. It may also contain small amounts of hydrogen and hydrogen sulfide.) | 649-085-00-1 | 271-001-3 | 68513-16-6 | H, K |
Gases (petroleum), light straight-run naphtha stabiliser off; Petroleum gas (A complex combination of hydrocarbons obtained by the stabilisation of light straight-run naphtha. It consists of saturated aliphatic hydrocarbons having carbon numbers predominantly in the range of C2 through C6.) | 649-086-00-7 | 271-002-9 | 68513-17-7 | H, K |
Residues (petroleum), alkylation splitter, C4-rich; Petroleum gas (A complex residuum from the distillation of streams from various refinery operations. It consists of hydrocarbons having carbon numbers in the range of C4 through C5, predominantly butane, and boiling in the range of approximately -11,7 °C to 27,8 °C.) | 649-087-00-2 | 271-010-2 | 68513-66-6 | H, K |
Hydrocarbons, C1-4; Petroleum gas (A complex combination of hydrocarbons provided by thermal cracking and absorber operations and by distillation of crude oil. It consists of hydrocarbons having carbon numbers predominantly in the range of C1 through C4 and boiling in the range of approximately - 164 °C to - 0,5 °C.) | 649-088-00-8 | 271-032-2 | 68514-31-8 | H, K |
Hydrocarbons, C1-4, sweetened; Petroleum gas (A complex combination of hydrocarbons obtained by subjecting hydrocarbon gases to a sweetening process to convert mercaptans or to remove acidic impurities. It consists of hydrocarbons having carbon numbers predominantly in the range of C1 through C4 and boiling in the range of approximately - 164 °C to - 0,5 °C.) | 649-089-00-3 | 271-038-5 | 68514-36-3 | H, K |
Hydrocarbons, C1-3; Petroleum gas (A complex combination of hydrocarbons having carbon numbers predominantly in the range of C1 through C3 and boiling in the range of approximately - 164 °C to - 42 °C.) | 649-090-00-9 | 271-259-7 | 68527-16-2 | H, K |
Hydrocarbons, C1-4, debutaniser fraction; Petroleum gas | 649-091-00-4 | 271-261-8 | 68527-19-5 | H, K |
Gases (petroleum), C1-5, wet; Petroleum gas (A complex combination of hydrocarbons produced by the distillation of crude oil and/or the cracking of tower gas oil. It consists of hydrocarbons having carbon numbers predominantly in the range of C1 through C5.) | 649-092-00-X | 271-624-0 | 68602-83-5 | H, K |
Hydrocarbons, C2-4; Petroleum gas | 649-093-00-5 | 271-734-9 | 68606-25-7 | H, K |
Hydrocarbons, C3; Petroleum gas | 649-094-00-0 | 271-735-4 | 68606-26-8 | H, K |
Gases (petroleum), alkylation feed; Petroleum gas (A complex combination of hydrocarbons produced by the catalytic cracking of gas oil. It consists of hydrocarbons having carbon numbers predominantly in the range of C3 through C4.) | 649-095-00-6 | 271-737-5 | 68606-27-9 | H, K |
Gases (petroleum), depropaniser bottoms fractionation off; Petroleum gas (A complex combination of hydrocarbons obtained from the fractionation of depropaniser bottoms. It consists predominantly of butane, isobutane and butadiene.) | 649-096-00-1 | 271-742-2 | 68606-34-8 | H, K |
Gases (petroleum), refinery blend; Petroleum gas (A complex combination obtained from various processes. It consists of hydrogen, hydrogen sulfide and hydrocarbons having carbon numbers predominantly in the range of C1 through C5.) | 649-097-00-7 | 272-183-7 | 68783-07-3 | H, K |
Gases (petroleum), catalytic cracking; Petroleum gas (A complex combination of hydrocarbons produced by the distillation of the products from a catalytic cracking process. It consists predominantly of hydrocarbons having carbon numbers predominantly in the range of C3 through C5.) | 649-098-00-2 | 272-203-4 | 68783-64-2 | H, K |
Gases (petroleum), C2-4, sweetened; Petroleum gas (A complex combination of hydrocarbons obtained by subjecting a petroleum distillate to a sweetening process to convert mercaptans or to remove acidic impurities. It consists predominantly of saturated and unsaturated hydrocarbons having carbon numbers predominantly in the range of C2 through C4 and boiling in the range of approximately - 51 °C to - 34 °C.) | 649-099-00-8 | 272-205-5 | 68783-65-3 | H, K |
Gases (petroleum), crude oil fractionation off; Petroleum gas (A complex combination of hydrocarbons produced by the fractionation of crude oil. It consists of saturated aliphatic hydrocarbons having carbon numbers predominantly in the range of C1 through C5.) | 649-100-00-1 | 272-871-7 | 68918-99-0 | H, K |
Gases (petroleum), dehexaniser off; Petroleum gas (A complex combination of hydrocarbons obtained by the fractionation of combined naphtha streams. It consists of saturated aliphatic hydrocarbons having carbon numbers predominantly in the range of C1 through C5.) | 649-101-00-7 | 272-872-2 | 68919-00-6 | H, K |
Gases (petroleum), light straight run gasoline fractionation stabiliser off; Petroleum gas (A complex combination of hydrocarbons obtained by the fractionation of light straight-run gasoline. It consists of saturated aliphatic hydrocarbons having carbon numbers predominantly in the range of C1 through C5.) | 649-102-00-2 | 272-878-5 | 68919-05-1 | H, K |
Gases (petroleum), naphtha unifiner desulphurisation stripper off; Petroleum gas (A complex combination of hydrocarbons produced by a naphtha unifiner desulphurisation process and stripped from the naphtha product. It consists of saturated aliphatic hydrocarbons having carbon numbers predominantly in the range of C1 through C4.) | 649-103-00-8 | 272-879-0 | 68919-06-2 | H, K |
Gases (petroleum), straight-run naphtha catalytic reforming off; Petroleum gas (A complex combination of hydrocarbons obtained by the catalytic reforming of straight-run naphtha and fractionation of the total effluent. It consists of methane, ethane, and propane.) | 649-104-00-3 | 272-882-7 | 68919-09-5 | H, K |
Gases (petroleum), fluidised catalytic cracker splitter overheads; Petroleum gas (A complex combination of hydrocarbons produced by the fractionation of the charge to the C3-C4 splitter. It consists predominantly of C3 hydrocarbons.) | 649-105-00-9 | 272-893-7 | 68919-20-0 | H, K |
Gases (petroleum), straight-run stabiliser off; Petroleum gas (A complex combination of hydrocarbons obtained from the fractionation of the liquid from the first tower used in the distillation of crude oil. It consists of saturated aliphatic hydrocarbons having carbon numbers predominantly in the range of C1 through C4.) | 649-106-00-4 | 272-883-2 | 68919-10-8 | H, K |
Gases (petroleum), catalytic cracked naphtha debutaniser; Petroleum gas (A complex combination of hydrocarbons obtained from fractionation of catalytic cracked naphtha. It consists of hydrocarbons having carbon numbers predominantly in the range of C1 through C4.) | 649-107-00-X | 273-169-3 | 68952-76-1 | H, K |
Tail gas (petroleum), catalytic cracked distillate and naphtha stabiliser; Petroleum gas (A complex combination of hydrocarbons obtained by the fractionation of catalytic cracked naphtha and distillate. It consists predominantly of hydrocarbons having carbon numbers predominantly in the range of C1 through C4.) | 649-108-00-5 | 273-170-9 | 68952-77-2 | H, K |
Tail gas (petroleum), thermal-cracked distillate, gas oil and naphtha absorber; Petroleum gas (A complex combination of hydrocarbons obtained from the separation of thermal-cracked distillates, naphtha and gas oil. It consists predominantly of hydrocarbons having carbon numbers predominantly in the range of C1 through C6.) | 649-109-00-0 | 273-175-6 | 68952-81-8 | H, K |
Tail gas (petroleum), thermal cracked hydrocarbon fractionation stabiliser, petroleum coking; Petroleum gas (A complex combination of hydrocarbons obtained from the fractionation stabilisation of thermal cracked hydrocarbons from a petroleum coking process. It consists of hydrocarbons having carbon numbers predominantly in the range of C1 through C6.) | 649-110-00-6 | 273-176-1 | 68952-82-9 | H, K |
Gases (petroleum, light steam-cracked, butadiene conc.; Petroleum gas (A complex combination of hydrocarbons produced by the distillation of products from a thermal cracking process. It consists of hydrocarbons having a carbon number predominantly of C4.) | 649-111-00-1 | 273-265-5 | 68955-28-2 | H, K |
Gases (petroleum), straight-run naphtha catalytic reformer stabiliser overhead; Petroleum gas (A complex combination of hydrocarbons obtained by the catalytic reforming of straight-run naphtha and the fractionation of the total effluent. It consists of saturated aliphatic hydrocarbons having carbon numbers predominantly in the range of C2 through C4.) | 649-112-00-7 | 273-270-2 | 68955-34-0 | H, K |
Hydrocarbons, C4; Petroleum gas | 649-113-00-2 | 289-339-5 | 27741-01-3 | H, K |
Alkanes, C1-4, C3-rich; Petroleum gas | 649-114-00-8 | 292-456-4 | 90622-55-2 | H, K |
Gases (petroleum), steam-cracker C3-rich; Petroleum gas (A complex combination of hydrocarbons produced by the distillation of products from a steam cracking process. It consists predominantly of propylene with some propane and boils in the range of approximately - 70 °C to 0 °C.) | 649-115-00-3 | 295-404-9 | 92045-22-2 | H, K |
Hydrocarbons, C4, steam-cracker distillate; Petroleum gas (A complex combination of hydrocarbons produced by the distillation of the products of a steam cracking process. It consists predominantly of hydrocarbons having a carbon number of C4, predominantly 1-butene and 2-butene, containing also butane and isobutene and boiling in the range of approximately - 12 °C to 5 °C.) | 649-116-00-9 | 295-405-4 | 92045-23-3 | H, K |
Petroleum gases, liquefied, sweetened, C4 fraction; Petroleum gas (A complex combination of hydrocarbons obtained by subjecting a liquified petroleum gas mix to a sweetening process to oxidise mercaptans or to remove acidic impurities. It consists predominantly of C4 saturated and unsaturated hydrocarbons.) | 649-117-00-4 | 295-463-0 | 92045-80-2 | H, K |
Raffinates (petroleum), steam-cracked C4 fraction cuprous ammonium acetate extraction, C3-5 and C3-5 unsaturated, butadiene-free; Petroleum gas | 649-119-00-5 | 307-769-4 | 97722-19-5 | H, K |
Appendix 2
Point 28 — Carcinogens: category 1B (Table 3.1)/ category 2 (Table 3.2)
Substances | Index No | EC No | CAS No | Notes |
Beryllium | 004-001-00-7 | 231-150-7 | 7440-41-7 | |
Beryllium compounds with the exception of aluminium beryllium silicates | 004-002-00-2 | |||
Beryllium oxide | 004-003-00-8 | 215-133-1 | 1304-56-9 | E |
Sulfallate (ISO); 2-chlorallyl diethyldithiocarbamate | 006-038-00-4 | 202-388-9 | 95-06-7 | |
Dimethylcarbamoyl chloride | 006-041-00-0 | 201-208-6 | 79-44-7 | |
Diazomethane | 006-068-00-8 | 206-382-7 | 334-88-3 | |
Hydrazine | 007-008-00-3 | 206-114-9 | 302-01-2 | E |
N,N-Dimethylhydrazine | 007-012-00-5 | 200-316-0 | 57-14-7 | |
1,2-Dimethylhydrazine | 007-013-00-0 | 540-73-8 | E | |
Salts of hydrazine | 007-014-00-6 | |||
Isobutyl nitrite | 007-017-00-2 | 208-819-7 | 542-56-3 | E |
Hydrazobenzene; 1,2-diphenylhydrazine | 007-021-00-4 | 204-563-5 | 122-66-7 | |
Hydrazine bis(3-carboxy-4-hydroxybenzensulfonate) | 007-022-00-X | 405-030-1 | ||
Hexamethylphosphoric triamide; hexamethylphosphoramide | 015-106-00-2 | 211-653-8 | 680-31-9 | |
Dimethyl sulphate | 016-023-00-4 | 201-058-1 | 77-78-1 | E |
Diethyl sulphate | 016-027-00-6 | 200-589-6 | 64-67-5 | |
1,3-Propanesultone | 016-032-00-3 | 214-317-9 | 1120-71-4 | |
Dimethylsulfamoylchloride | 016-033-00-9 | 236-412-4 | 13360-57-1 | |
Potassium dichromate | 024-002-00-6 | 231-906-6 | 7778-50-9 | E |
Ammonium dichromate | 024-003-00-1 | 232-143-1 | 7789-09-5 | E |
Sodium dichromate anhydrate | 024-004-00-7 | 234-190-3 | 10588-01-9 | E |
Sodium dichromate, dihydrate | 024-004-01-4 | 234-190-3 | 7789-12-0 | E |
Chromyl dichloride; chromic oxychloride | 024-005-00-2 | 239-056-8 | 14977-61-8 | |
Potassium chromate | 024-006-00-8 | 232-140-5 | 7789-00-6 | |
Calcium chromate | 024-008-00-9 | 237-366-8 | 13765-19-0 | |
Strontium chromate | 024-009-00-4 | 232-142-6 | 7789-06-2 | |
Chromium III chromate; chromic chromate | 024-010-00-X | 246-356-2 | 24613-89-6 | |
Chromium (VI) compounds, with the exception of barium chromate and of compounds specified elsewhere in ►M3 Annex VI to Regulation (EC) No 1272/2008 ◄ | 024-017-00-8 | — | — | |
Sodium chromate | 024-018-00-3 | 231-889-5 | 7775-11-3 | E |
Cobalt dichloride | 027-004-00-5 | 231-589-4 | 7646-79-9 | E |
Cobalt sulphate | 027-005-00-0 | 233-334-2 | 10124-43-3 | E |
Potassium bromate | 035-003-00-6 | 231-829-8 | 7758-01-2 | |
Cadmium oxide | 048-002-00-0 | 215-146-2 | 1306-19-0 | E |
Cadmium fluoride | 048-006-00-2 | 232-222-0 | 7790-79-6 | E |
Cadmium chloride | 048-008-00-3 | 233-296-7 | 10108-64-2 | E |
Cadmium sulphate | 048-009-00-9 | 233-331-6 | 10124-36-4 | E |
Cadmium sulphide | 048-010-00-4 | 215-147-8 | 1306-23-6 | E |
Cadmium (pyrophoric) | 048-011-00-X | 231-152-8 | 7440-43-9 | E |
Isoprene (stabilised) 2-Methyl-1,3-butadiene | 601-014-00-5 | 201-143-3 | 78-79-5 | D |
Benzo[a]pyrene; benzo[d,e,f]chrysene | 601-032-00-3 | 200-028-5 | 50-32-8 | |
Benzo[a]anthracene | 601-033-00-9 | 200-280-6 | 56-55-3 | |
Benzo[b]fluoranthene; benzo[e]acephenanthrylene | 601-034-00-4 | 205-911-9 | 205-99-2 | |
Benzo[j]fluoranthene | 601-035-00-X | 205-910-3 | 205-82-3 | |
Benzo[k]fluoranthene | 601-036-00-5 | 205-916-6 | 207-08-9 | |
Dibenz[a, h]anthracene | 601-041-00-2 | 200-181-8 | 53-70-3 | |
Chrysene | 601-048-00-0 | 205-923-4 | 218-01-9 | |
Benzo[e]pyrene | 601-049-00-6 | 205-892-7 | 192-97-2 | |
1,2-Dibromoethane; ethylene dibromide | 602-010-00-6 | 203-444-5 | 106-93-4 | E |
1,2-Dichloroethane; ethylene dichloride | 602-012-00-7 | 203-458-1 | 107-06-2 | |
1,2-Dibromo-3-chloropropane | 602-021-00-6 | 202-479-3 | 96-12-8 | |
Bromoethylene | 602-024-00-2 | 209-800-6 | 593-60-2 | |
Trichloroethylene; trichloroethene | 602-027-00-9 | 201-167-4 | 79-01-6 | |
Chloroprene (stabilised) 2-Chlorobuta-1,3-diene | 602-036-00-8 | 204-818-0 | 126-99-8 | D, E |
α-Chlorotoluene; benzyl chloride | 602-037-00-3 | 202-853-6 | 100-44-7 | E |
α,α,α-Trichlorotoluene; benzotrichloride | 602-038-00-9 | 202-634-5 | 98-07-7 | |
1,2,3-Trichloropropane | 602-062-00-X | 202-486-1 | 96-18-4 | D |
1,3-Dichloro-2-propanol | 602-064-00-0 | 202-491-9 | 96-23-1 | |
Hexachlorobenzene | 602-065-00-6 | 204-273-9 | 118-74-1 | |
1,4-Dichlorobut-2-ene | 602-073-00-X | 212-121-8 | 764-41-0 | E |
2,3-dibromopropan-1-ol; 2,3-dibromo-1-propanol | 602-088-00-1 | 202-480-9 | 96-13-9 | E |
α,α,α,4-Tetrachlorotoluene p-Chlorobenzotrichloride | 602-093-00-9 | 226-009-1 | 5216-25-1 | E |
Ethylene oxide; oxirane | 603-023-00-X | 200-849-9 | 75-21-8 | |
1-Chloro-2,3-epoxypropane; epichlorhydrin | 603-026-00-6 | 203-439-8 | 106-89-8 | |
Propylene oxide; 1,2-epoxypropane; methyloxirane | 603-055-00-4 | 200-879-2 | 75-56-9 | E |
2,2'-Bioxirane; 1,2:3,4-diepoxybutane | 603-060-00-1 | 215-979-1 | 1464-53-5 | |
2,3-Epoxypropan-1-ol; glycidol oxiranemethanol | 603-063-00-8 | 209-128-3 | 556-52-5 | E |
Phenyl glycidyl ether; 2,3-epoxypropyl phenyl ether; 1,2-epoxy-3-phenoxypropane | 603-067-00-X | 204-557-2 | 122-60-1 | E |
Styrene oxide; (epoxyethyl)benzene; phenyloxirane | 603-084-00-2 | 202-476-7 | 96-09-3 | |
Furan | 603-105-00-5 | 203-727-3 | 110-00-9 | E |
R-2,3-epoxy-1-propanol | 603-143-00-2 | 404-660-4 | 57044-25-4 | E |
(R)-1-chloro-2,3-epoxypropane | 603-166-00-8 | 424-280-2 | 51594-55-9 | |
4-Amino-3-fluorophenol | 604-028-00-X | 402-230-0 | 399-95-1 | |
5-Allyl-1,3-benzodioxole; safrole | 605-020-00-9 | 202-345-4 | 94-59-7 | E |
3-Propanolide; 1,3-propiolactone | 606-031-00-1 | 200-340-1 | 57-57-8 | |
4,4'-Bis(dimethylamino)benzophenone Michler's ketone | 606-073-00-0 | 202-027-5 | 90-94-8 | |
Urethane(INN); ethyl carbamate | 607-149-00-6 | 200-123-1 | 51-79-6 | |
Methyl acrylamidomethoxyacetate (containing ≥ 0,1 % acrylamide) | 607-190-00-X | 401-890-7 | 77402-03-0 | |
Methyl acrylamidoglycolate (containing ≥ 0,1 % acrylamide) | 607-210-00-7 | 403-230-3 | 77402-05-2 | |
Oxiranemethanol, 4-methylbenzene-sulfonate, (S)- | 607-411-00-X | 417-210-7 | 70987-78-9 | |
Acrylonitrile | 608-003-00-4 | 203-466-5 | 107-13-1 | D, E |
2-Nitropropane | 609-002-00-1 | 201-209-1 | 79-46-9 | |
2,4-Dinitrotoluene [1]; dinitrotoluene [2]; dinitrotoluene, technical grade | 609-007-00-9 | 204-450-0 [1] 246-836-1 [2] | 121-14-2 [1] 25321-14-6 [2] | E |
5-Nitroacenaphthene | 609-037-00-2 | 210-025-0 | 602-87-9 | |
2-Nitronaphthalene | 609-038-00-8 | 209-474-5 | 581-89-5 | |
4-Nitrobiphenyl | 609-039-00-3 | 202-204-7 | 92-93-3 | |
Nitrofen (ISO); 2,4-dichlorophenyl4-nitrophenyl ether | 609-040-00-9 | 217-406-0 | 1836-75-5 | |
2-Nitroanisole | 609-047-00-7 | 202-052-1 | 91-23-6 | |
2,6-Dinitrotoluene | 609-049-00-8 | 210-106-0 | 606-20-2 | E |
2,3-dinitrotoluene | 609-050-00-3 | 210-013-5 | 602-01-7 | E |
3,4-dinitrotoluene | 609-051-00-9 | 210-222-1 | 610-39-9 | E |
3,5-dinitrotoluene | 609-052-00-4 | 210-566-2 | 618-85-9 | E |
Hydrazine-tri-nitromethane | 609-053-00-X | 414-850-9 | — | |
2,5-dinitrotoluene | 609-055-00-0 | 210-581-4 | 619-15-8 | E |
2-Nitrotoluene | 609-065-00-5 | 201-853-3 | 88-72-2 | E |
Azobenzene | 611-001-00-6 | 203-102-5 | 103-33-3 | E |
Methyl-ONN-azoxymethyl acetate; methyl azoxy methyl acetate | 611-004-00-2 | 209-765-7 | 592-62-1 | |
Disodium {5-[(4′-((2,6-hydroxy-3-((2-hydroxy-5-sulphophenyl)azo)phenyl)azo) (1,1′-biphenyl)-4-yl)azo]salicylato(4-)} cuprate(2-); CI Direct Brown 95 | 611-005-00-8 | 240-221-1 | 16071-86-6 | |
4-o-Tolylazo-o-toluidine; 4-amino-2′,3-dimethylazobenzene; fast garnet GBC base; AAT; o-aminoazotoluene | 611-006-00-3 | 202-591-2 | 97-56-3 | |
4-Aminoazobenzene | 611-008-00-4 | 200-453-6 | 60-09-3 |
Appendix 3
Point 29 — Mutagens: category 1A (Table 3.1)/category 1 (Table 3.2)
Appendix 4
Point 29 — Mutagens: category 1B (Table 3.1)/category 2 (Table 3.2)
Substances | Index No | EC No | CAS No | Notes |
Hexamethylphosphoric triamide; hexamethylphosphoramide | 015-106-00-2 | 211-653-8 | 680-31-9 | |
Diethyl sulphate | 016-027-00-6 | 200-589-6 | 64-67-5 | |
Chromium (VI) trioxide | 024-001-00-0 | 215-607-8 | 1333-82-0 | E |
Potassium dichromate | 024-002-00-6 | 231-906-6 | 7778-50-9 | E |
Ammonium dichromate | 024-003-00-1 | 232-143-1 | 7789-09-5 | E |
Sodium dichromate anhydrate | 024-004-00-7 | 234-190-3 | 10588-01-9 | E |
Sodium dichromate, dihydrate | 024-004-01-4 | 234-190-3 | 7789-12-0 | E |
Chromyl dichloride; chromic oxychloride | 024-005-00-2 | 239-056-8 | 14977-61-8 | |
Potassium chromate | 024-006-00-8 | 232-140-5 | 7789-00-6 | |
Sodium chromate | 024-018-00-3 | 231-889-5 | 7775-11-3 | E |
Cadmium fluoride | 048-006-00-2 | 232-222-0 | 7790-79-6 | E |
Cadmium chloride | 048-008-00-3 | 233-296-7 | 10108-64-2 | E |
Cadmium sulphate | 048-009-00-9 | 233-331-6 | 10124-36-4 | E |
Butane [containing ≥ 0,1 % Butadiene (203-450-8)] [1] | 601-004-01-8 | 203-448-7 [1] | 106-97-8 [1] | C, S |
Isobutane [containing ≥ 0,1 % Butadiene (203-450-8)] [2] | 20-857-2 [2] | 75-28-5 [2] | ||
1,3-Butadiene buta-1,3-diene | 601-013-00-X | 203-450-8 | 106-99-0 | D |
Benzene | 601-020-00-8 | 200-753-7 | 71-43-2 | E |
Benzo[a]pyrene; benzo[d,e,f]chrysene | 601-032-00-3 | 200-028-5 | 50-32-8 | |
1,2-Dibromo-3-chloropropane | 602-021-00-6 | 202-479-3 | 96-12-8 | |
Ethylene oxide; oxirane | 603-023-00-X | 200-849-9 | 75-21-8 | |
Propylene oxide; 1,2-epoxypropane; Methyloxirane | 603-055-00-4 | 200-879-2 | 75-56-9 | E |
2,2'-Bioxirane; 1,2:3,4-diepoxybutane | 603-060-00-1 | 215-979-1 | 1464-53-5 | |
Methyl acrylamidomethoxyacetate (containing ≥ 0,1 % acrylamide) | 607-190-00-X | 401-890-7 | 77402-03-0 | |
Methyl acrylamidoglycolate (containing ≥ 0,1 % acrylamide) | 607-210-00-7 | 403-230-3 | 77402-05-2 | |
2-Nitrotoluene | 609-065-00-5 | 201-853-3 | 88-72-2 | E |
4,4'-oxydianiline [1] and its salts p-aminophenyl ether [1] | 612-199-00-7 | 202-977-0 [1] | 101-80-4 [1] | E |
Ethyleneimine; aziridine | 613-001-00-1 | 205-793-9 | 151-56-4 | |
Carbendazim (ISO) methyl benzimidazol-2-ylcarbamate | 613-048-00-8 | 234-232-0 | 10605-21-7 | |
Benomyl (ISO) methyl 1-(butylcarbamoyl)benzimidazol-2-ylcarbamate | 613-049-00-3 | 241-775-7 | 17804-35-2 | |
1,3,5,-Tris(oxiranylmethyl)-1,3,5-triazine-2,4,6(1H,3H,5H)-trione; TGIC | 615-021-00-6 | 219-514-3 | 2451-62-9 | |
Acrylamide | 616-003-00-0 | 201-173-7 | 79-06-1 | |
1,3,5-tris-[(2S and 2R)-2,3-epoxypropyl]-1,3,5-triazine-2,4,6-(1H,3H,5H)-trione | 616-091-00-0 | 423-400-0 | 59653-74-6 | E |
Gases (petroleum), catalytic cracked naphtha depropaniser overhead, C3-rich acid-free; Petroleum gas (A complex combination of hydrocarbons obtained from fractionation of catalytic cracked hydrocarbons and treated to remove acidic impurities. It consists of hydrocarbons having carbon numbers in the range of C2 through C4, predominantly C3.) | 649-062-00-6 | 270-755-0 | 68477-73-6 | H, K |
Gases (petroleum), catalytic cracker; Petroleum gas (A complex combination of hydrocarbons produced by the distillation of the products from a catalytic cracking process. It consists predominantly of aliphatic hydrocarbons having carbon numbers predominantly in the range of C1 through C6.) | 649-063-00-1 | 270-756-6 | 68477-74-7 | H, K |
Gases (petroleum), catalytic cracker, C1-5-rich; Petroleum gas (A complex combination of hydrocarbons produced by the distillation of products from a catalytic cracking process. It consists of aliphatic hydrocarbons having carbon numbers in the range of C1 through C6, predominantly C1 through C5.) | 649-064-00-7 | 270-757-1 | 68477-75-8 | H, K |
Gases (petroleum), catalytic polymd. naphtha stabiliser overhead, C2-4-rich; Petroleum gas (A complex combination of hydrocarbons obtained from the fractionation stabilisation of catalytic polymerised naphtha. It consists of aliphatic hydrocarbons having carbon numbers in the range of C2 through C6, predominantly C2 through C4.) | 649-065-00-2 | 270-758-7 | 68477-76-9 | H, K |
Gases (petroleum), catalytic reformer, C1-4-rich; Petroleum gas (A complex combination of hydrocarbons produced by distillation of products from a catalytic reforming process. It consists of hydrocarbons having carbon numbers in the range of C1 through C6, predominantly C1 through C4.) | 649-066-00-8 | 270-760-8 | 68477-79-2 | H, K |
Gases (petroleum), C3-5 olefinic-paraffinic alkylation feed; Petroleum gas (A complex combination of olefinic and paraffinic hydrocarbons having carbon numbers in the range of C3 through C5 which are used as alkylation feed. Ambient temperatures normally exceed the critical temperature of these combinations.) | 649-067-00-3 | 270-765-5 | 68477-83-8 | H, K |
Gases (petroleum), C4-rich; Petroleum gas (A complex combination of hydrocarbons produced by distillation of products from a catalytic fractionation process. It consists of aliphatic hydrocarbons having carbon numbers in the range of C3 through C5, predominantly C4.) | 649-068-00-9 | 270-767-6 | 68477-85-0 | H, K |
Gases (petroleum), deethaniser overheads; Petroleum gas (A complex combination of hydrocarbons produced from distillation of the gas and gasoline fractions from the catalytic cracking process. It contains predominantly ethane and ethylene.) | 649-069-00-4 | 270-768-1 | 68477-86-1 | H, K |
Gases (petroleum), deisobutaniser tower overheads; Petroleum gas (A complex combination of hydrocarbons produced by the atmospheric distillation of a butane-butylene stream. It consists of aliphatic hydrocarbons having carbon numbers predominantly in the range of C3 through C4.) | 649-070-00-X | 270-769-7 | 68477-87-2 | H, K |
Gases (petroleum), depropaniser dry, propene-rich; Petroleum gas (A complex combination of hydrocarbons produced by the distillation of products from the gas and gasoline fractions of a catalytic cracking process. It consists predominantly of propylene with some ethane and propane.) | 649-071-00-5 | 270-772-3 | 68477-90-7 | H, K |
Gases (petroleum), depropaniser overheads; Petroleum gas (A complex combination of hydrocarbons produced by distillation of products from the gas and gasoline fractions of a catalytic cracking process. It consists of aliphatic hydrocarbons having carbon numbers predominantly in the range of C2 through C4.) | 649-072-00-0 | 270-773-9 | 68477-91-8 | H, K |
Gases (petroleum), gas recovery plant depropaniser overheads; Petroleum gas (A complex combination of hydrocarbons obtained by fractionation of miscellaneous hydrocarbon streams. It consists predominantly of hydrocarbons having carbon numbers in the range of C1 through C4, predominantly propane.) | 649-073-00-6 | 270-777-0 | 68477-94-1 | H, K |
Gases (petroleum), Girbatol unit feed; Petroleum gas (A complex combination of hydrocarbons that is used as the feed into the Girbatol unit to remove hydrogen sulfide. It consists of aliphatic hydrocarbons having carbon numbers predominantly in the range of C2 through C4.) | 649-074-00-1 | 270-778-6 | 68477-95-2 | H, K |
Gases (petroleum), isomerised naphtha fractionator, C4-rich, hydrogen sulfide-free; Petroleum gas | 649-075-00-7 | 270-782-8 | 68477-99-6 | H, K |
Tail gas (petroleum), catalytic cracked clarified oil and thermal cracked vacuum residue fractionation reflux drum; Petroleum gas (A complex combination of hydrocarbons obtained from fractionation of catalytic cracked clarified oil and thermal cracked vacuum residue. It consists predominantly of hydrocarbons having carbon numbers predominantly in the range of C1 through C6.) | 649-076-00-2 | 270-802-5 | 68478-21-7 | H, K |
Tail gas (petroleum), catalytic cracked naphtha stabilisation absorber; Petroleum gas (A complex combination of hydrocarbons obtained from the stabilisation of catalytic cracked naphtha. It consists predominantly of hydrocarbons having carbon numbers predominantly in the range of C1 through C6.) | 649-077-00-8 | 270-803-0 | 68478-22-8 | H, K |
Tail gas (petroleum), catalytic cracker, catalytic reformer and hydrodesulphuriser combined fractionater; Petroleum gas (A complex combination of hydrocarbons obtained from the fractionation of products from catalytic cracking, catalytic reforming and hydrodesulphurising processes treated to remove acidic impurities. It consists predominantly of hydrocarbons having carbon numbers predominantly in the range of C1 through C5.) | 649-078-00-3 | 270-804-6 | 68478-24-0 | H, K |
Tail gas (petroleum), catalytic reformed naphtha fractionation stabiliser; Petroleum gas (A complex combination of hydrocarbons obtained from the fractionation stabilisation of catalytic reformed naphtha. It consists predominantly of hydrocarbons having carbon numbers predominantly in the range of C1 through C4.) | 649-079-00-9 | 270-806-7 | 68478-26-2 | H, K |
Tail gas (petroleum), saturate gas plant mixed stream, C4-rich; Petroleum gas (A complex combination of hydrocarbons obtained from the fractionation stabilisation of straight-run naphtha, distillation tail gas and catalytic reformed naphtha stabiliser tail gas. It consists of hydrocarbons having carbon numbers in the range of C3 through C6, predominantly butane and isobutane.) | 649-080-00-4 | 270-813-5 | 68478-32-0 | H, K |
Tail gas (petroleum), saturate gas recovery plant, C1-2-rich; Petroleum gas (A complex combination of hydrocarbons obtained from fractionation of distillate tail gas, straight-run naphtha, catalytic reformed naphtha stabiliser tail gas. It consists predominantly of hydrocarbons having carbon numbers in the range of C1 through C5, predominantly methane and ethane.) | 649-081-00-X | 270-814-0 | 68478-33-1 | H, K |
Tail gas (petroleum), vacuum residues thermal cracker; Petroleum gas (A complex combination of hydrocarbons obtained from the thermal cracking of vacuum residues. It consists of hydrocarbons having carbon numbers predominantly in the range of C1 through C5.) | 649-082-00-5 | 270-815-6 | 68478-34-2 | H, K |
Hydrocarbons, C3-4-rich, petroleum distillate; Petroleum gas (A complex combination of hydrocarbons produced by distillation and condensation of crude oil. It consists of hydrocarbons having carbon numbers in the range of C3 through C5, predominantly C3 through C4.) | 649-083-00-0 | 270-990-9 | 68512-91-4 | H, K |
Gases (petroleum), full-range straight-run naphtha dehexaniser off; Petroleum gas (A complex combination of hydrocarbons obtained by the fractionation of the full-range straight-run naphtha. It consists of hydrocarbons having carbon numbers predominantly in the range of C2 through C6.) | 649-084-00-6 | 271-000-8 | 68513-15-5 | H, K |
Gases (petroleum), hydrocracking depropaniser off, hydrocarbon-rich; Petroleum gas (A complex combination of hydrocarbon produced by the distillation of products from a hydrocracking process. It consists predominantly of hydrocarbons having carbon numbers predominantly in the range of C1 through C4. It may also contain small amounts of hydrogen and hydrogen sulfide.) | 649-085-00-1 | 271-001-3 | 68513-16-6 | H, K |
Gases (petroleum), light straight-run naphtha stabiliser off; Petroleum gas (A complex combination of hydrocarbons obtained by the stabilisation of light straight-run naphtha. It consists of saturated aliphatic hydrocarbons having carbon numbers predominantly in the range of C2 through C6.) | 649-086-00-7 | 271-002-9 | 68513-17-7 | H, K |
Residues (petroleum), alkylation splitter, C4-rich; Petroleum gas (A complex residuum from the distillation of streams from various refinery operations. It consists of hydrocarbons having carbon numbers in the range of C4 through C5, predominantly butane, and boiling in the range of approximately -11,7 °C to 27,8 °C.) | 649-087-00-2 | 271-010-2 | 68513-66-6 | H, K |
Hydrocarbons, C1-4; Petroleum gas (A complex combination of hydrocarbons provided by thermal cracking and absorber operations and by distillation of crude oil. It consists of hydrocarbons having carbon numbers predominantly in the range of C1 through C4 and boiling in the range of approximately minus 164 °C to minus 0,5 °C.) | 649-088-00-8 | 271-032-2 | 68514-31-8 | H, K |
Hydrocarbons, C1-4, sweetened; Petroleum gas (A complex combination of hydrocarbons obtained by subjecting hydrocarbon gases to a sweetening process to convert mercaptans or to remove acidic impurities. It consists of hydrocarbons having carbon numbers predominantly in the range of C1 through C4 and boiling in the range of approximately - 164 °C to - 0,5 °C.) | 649-089-00-3 | 271-038-5 | 68514-36-3 | H, K |
Hydrocarbons, C1-3; Petroleum gas (A complex combination of hydrocarbons having carbon numbers predominantly in the range of C1 through C3 and boiling in the range of approximately - 164 °C to - 42 °C.) | 649-090-00-9 | 271-259-7 | 68527-16-2 | H, K |
Hydrocarbons, C1-4, debutaniser fraction; Petroleum gas | 649-091-00-4 | 271-261-8 | 68527-19-5 | H, K |
Gases (petroleum), C1-5, wet; Petroleum gas (A complex combination of hydrocarbons produced by the distillation of crude oil and/or the cracking of tower gas oil. It consists of hydrocarbons having carbon numbers predominantly in the range of C1 through C5.) | 649-092-00-X | 271-624-0 | 68602-83-5 | H, K |
Hydrocarbons, C2-4; Petroleum gas | 649-093-00-5 | 271-734-9 | 68606-25-7 | H, K |
Hydrocarbons, C3; Petroleum gas | 649-094-00-0 | 271-735-4 | 68606-26-8 | H, K |
Gases (petroleum), alkylation feed; Petroleum gas (A complex combination of hydrocarbons produced by the catalytic cracking of gas oil. It consists of hydrocarbons having carbon numbers predominantly in the range of C3 through C4.) | 649-095-00-6 | 271-737-5 | 68606-27-9 | H, K |
Gases (petroleum), depropaniser bottoms fractionation off; Petroleum gas (A complex combination of hydrocarbons obtained from the fractionation of depropaniser bottoms. It consists predominantly of butane, isobutane and butadiene.) | 649-096-00-1 | 271-742-2 | 68606-34-8 | H, K |
Gases (petroleum), refinery blend; Petroleum gas (A complex combination obtained from various processes. It consists of hydrogen, hydrogen sulfide and hydrocarbons having carbon numbers predominantly in the range of C1 through C5.) | 649-097-00-7 | 272-183-7 | 68783-07-3 | H, K |
Gases (petroleum), catalytic cracking; Petroleum gas (A complex combination of hydrocarbons produced by the distillation of the products from a catalytic cracking process. It consists predominantly of hydrocarbons having carbon numbers predominantly in the range of C3 through C5.) | 649-098-00-2 | 272-203-4 | 68783-64-2 | H, K |
Gases (petroleum), C2-4, sweetened; Petroleum gas (A complex combination of hydrocarbons obtained by subjecting a petroleum distillate to a sweetening process to convert mercaptans or to remove acidic impurities. It consists predominantly of saturated and unsaturated hydrocarbons having carbon numbers predominantly in the range of C2 through C4 and boiling in the range of approximately - 51 °C to - 34 °C.) | 649-099-00-8 | 272-205-5 | 68783-65-3 | H, K |
Gases (petroleum), crude oil fractionation off; Petroleum gas (A complex combination of hydrocarbons produced by the fractionation of crude oil. It consists of saturated aliphatic hydrocarbons having carbon numbers predominantly in the range of C1 through C5.) | 649-100-00-1 | 272-871-7 | 68918-99-0 | H, K |
Gases (petroleum), dehexaniser off; Petroleum gas (A complex combination of hydrocarbons obtained by the fractionation of combined naphtha streams. It consists of saturated aliphatic hydrocarbons having carbon numbers predominantly in the range of C1 through C5.) | 649-101-00-7 | 272-872-2 | 68919-00-6 | H, K |
Gases (petroleum), light straight run gasoline fractionation stabiliser off; Petroleum gas (A complex combination of hydrocarbons obtained by the fractionation of light straight-run gasoline. It consists of saturated aliphatic hydrocarbons having carbon numbers predominantly in the range of C1 through C5.) | 649-102-00-2 | 272-878-5 | 68919-05-1 | H, K |
Gases (petroleum), naphtha unifiner desulphurisation stripper off; Petroleum gas (A complex combination of hydrocarbons produced by a naphtha unifiner desulphurisation process and stripped from the naphtha product. It consists of saturated aliphatic hydrocarbons having carbon numbers predominantly in the range of C1 through C4.) | 649-103-00-8 | 272-879-0 | 68919-06-2 | H, K |
Gases (petroleum), straight-run naphtha catalytic reforming off; Petroleum gas (A complex combination of hydrocarbons obtained by the catalytic reforming of straight-run naphtha and fractionation of the total effluent. It consists of methane, ethane, and propane.) | 649-104-00-3 | 272-882-7 | 68919-09-5 | H, K |
Gases (petroleum), fluidised catalytic cracker splitter overheads; Petroleum gas (A complex combination of hydrocarbons produced by the fractionation of the charge to the C3-C4 splitter. It consists predominantly of C3 hydrocarbons.) | 649-105-00-9 | 272-893-7 | 68919-20-0 | H, K |
Gases (petroleum), straight-run stabiliser off; Petroleum gas (A complex combination of hydrocarbons obtained from the fractionation of the liquid from the first tower used in the distillation of crude oil. It consists of saturated aliphatic hydrocarbons having carbon numbers predominantly in the range of C1 through C4.) | 649-106-00-4 | 272-883-2 | 68919-10-8 | H, K |
Gases (petroleum), catalytic cracked naphtha debutaniser; Petroleum gas (A complex combination of hydrocarbons obtained from fractionation of catalytic cracked naphtha. It consists of hydrocarbons having carbon numbers predominantly in the range of C1 through C4.) | 649-107-00-X | 273-169-3 | 68952-76-1 | H, K |
Tail gas (petroleum), catalytic cracked distillate and naphtha stabiliser; Petroleum gas (A complex combination of hydrocarbons obtained by the fractionation of catalytic cracked naphtha and distillate. It consists predominantly of hydrocarbons having carbon numbers predominantly in the range of C1 through C4.) | 649-108-00-5 | 273-170-9 | 68952-77-2 | H, K |
Tail gas (petroleum), thermal-cracked distillate, gas oil and naphtha absorber; Petroleum gas (A complex combination of hydrocarbons obtained from the separation of thermal-cracked distillates, naphtha and gas oil. It consists predominantly of hydrocarbons having carbon numbers predominantly in the range of C1 through C6.) | 649-109-00-0 | 273-175-6 | 68952-81-8 | H, K |
Tail gas (petroleum), thermal cracked hydrocarbon fractionation stabiliser, petroleum coking; Petroleum gas (A complex combination of hydrocarbons obtained from the fractionation stabilisation of thermal cracked hydrocarbons from a petroleum coking process. It consists of hydrocarbons having carbon numbers predominantly in the range of C1 through C6.) | 649-110-00-6 | 273-176-1 | 68952-82-9 | H, K |
Gases (petroleum, light steam-cracked, butadiene concentrate; Petroleum gas (A complex combination of hydrocarbons produced by the distillation of products from a thermal cracking process. It consists of hydrocarbons having a carbon number predominantly of C4.) | 649-111-00-1 | 273-265-5 | 68955-28-2 | H, K |
Gases (petroleum), straight-run naphtha catalytic reformer stabiliser overhead; Petroleum gas (A complex combination of hydrocarbons obtained by the catalytic reforming of straight-run naphtha and the fractionation of the total effluent. It consists of saturated aliphatic hydrocarbons having carbon numbers predominantly in the range of C2 through C4.) | 649-112-00-7 | 273-270-2 | 68955-34-0 | H, K |
Hydrocarbons, C4; Petroleum gas | 649-113-00-2 | 289-339-5 | 87741-01-3 | H, K |
Alkanes, C1-4, C3-rich; Petroleum gas | 649-114-00-8 | 292-456-4 | 90622-55-2 | H, K |
Gases (petroleum), steam-cracker C3-rich; Petroleum gas (A complex combination of hydrocarbons produced by the distillation of products from a steam cracking process. It consists predominantly of propylene with some propane and boils in the range of approximately - 70 °C to 0 °C.) | 649-115-00-3 | 295-404-9 | 92045-22-2 | H, K |
Hydrocarbons, C4, steam-cracker distillate; Petroleum gas (A complex combination of hydrocarbons produced by the distillation of the products of a steam cracking process. It consists predominantly of hydrocarbons having a carbon number of C4, predominantly 1-butene and 2-butene, containing also butane and isobutene and boiling in the range of approximately - 12 °C to 5 °C.) | 649-116-00-9 | 295-405-4 | 92045-23-3 | H, K |
Petroleum gases, liquefied, sweetened, C4 fraction; Petroleum gas (A complex combination of hydrocarbons obtained by subjecting a liquified petroleum gas mix to a sweetening process to oxidise mercaptans or to remove acidic impurities. It consists predominantly of C4 saturated and unsaturated hydrocarbons.) | 649-117-00-4 | 295-463-0 | 92045-80-2 | H, K, S |
Raffinates (petroleum), steam-cracked C4 fraction cuprous ammonium acetate extraction, C3-5 and C3-5 unsaturated., butadiene-free; Petroleum gas | 649-119 -00-5 | 307-769-4 | 97722-19-5 | H, K |
Gases (petroleum), amine system feed; Refinery gas (The feed gas to the amine system for removal of hydrogen sulphide. It consists primarily of hydrogen. Carbon monoxide, carbon dioxide, hydrogen sulfide and aliphatic hydrocarbons having carbon numbers predominantly in the range of C1 through C5 may also be present.) | 649-120-00-0 | 270-746-1 | 68477-65-6 | H, K |
Gases (petroleum), benzene unit hydrodesulphuriser off; Refinery gas (Off gases produced by the benzene unit. It consists primarily of hydrogen. Carbon monoxide and hydrocarbons having carbon numbers predominantly in the range of C1 through C6, including benzene, may also be present.) | 649-121-00-6 | 270-747-7 | 68477-66-7 | H, K |
Gases (petroleum), benzene unit recycle, hydrogen-rich; Refinery gas (A complex combination of hydrocarbons obtained by recycling the gases of the benzene unit. It consists primarily of hydrogen with various small amounts of carbon monoxide and hydrocarbons having carbon numbers in the range of C1 through C6.) | 649-122-00-1 | 270-748-2 | 68477-67-8 | H, K |
Gases (petroleum), blend oil, hydrogen-nitrogen-rich; Refinery gas (A complex combination of hydrocarbons obtained by distillation of a blend oil. It consists primarily of hydrogen and nitrogen with various small amounts of carbon monoxide, carbon dioxide, and aliphatic hydrocarbons having carbon numbers predominantly in the range of C1 through C5.) | 649-123-00-7 | 270-749-8 | 68477-68-9 | H, K |
Gases (petroleum), catalytic reformed naphtha stripper overheads; Refinery gas (A complex combination of hydrocarbons obtained from stabilisation of catalytic reformed naphtha. It consists of hydrogen and saturated hydrocarbons having carbon numbers predominantly in the range of C1 through C4.) | 649-124-00-2 | 270-759-2 | 68477-77-0 | H, K |
Gases (petroleum), C6-8 catalytic reformer recycle; Refinery gas (A complex combination of hydrocarbons produced by distillation of products from catalytic reforming of C6-C8 feed and recycled to conserve hydrogen. It consists primarily of hydrogen. It may also contain various small amounts of carbon monoxide, carbon dioxide, nitrogen, and hydrocarbons having carbon numbers predominantly in the range of C1 through C6.) | 649-125-00-8 | 270-761-3 | 68477-80-5 | H, K |
Gases (petroleum), C6-8 catalytic reformer; Refinery gas (A complex combination of hydrocarbons produced by distillation of products from catalytic reforming of C6-C8 feed. It consists of hydrocarbons having carbon numbers in the range of C1 through C5 and hydrogen.) | 649-126-00-3 | 270-762-9 | 68477-81-6 | H, K |
Gases (petroleum), C6-8 catalytic reformer recycle, hydrogen-rich; Refinery gas | 649-127-00-9 | 270-763-4 | 68477-82-7 | H, K |
Gases (petroleum), C2-return stream; Refinery gas (A complex combination of hydrocarbons obtained by the extraction of hydrogen from a gas stream which consists primarily of hydrogen with small amounts of nitrogen, carbon monoxide, methane, ethane, and ethylene. It contains predominantly hydrocarbons such as methane, ethane, and ethylene with small amounts of hydrogen, nitrogen and carbon monoxide.) | 649-128-00-4 | 270-766-0 | 68477-84-9 | H, K |
Gases (petroleum), dry sour, gas-concentration-unit-off; Refinery gas (The complex combination of dry gases from a gas concentration unit. It consists of hydrogen, hydrogen sulphide and hydrocarbons having carbon numbers predominantly in the range of C1 through C3.) | 649-129-00-X | 270-774-4 | 68477-92-9 | H, K |
Appendix 5
Point 30 — Reproductive toxicants: category 1A (Table 3.1)/category 1 (Table 3.2)
Substances | Index No | EC No | CAS No | Notes |
Carbon monoxide | 006-001-00-2 | 211-128-3 | 630-08-0 | |
Lead hexafluorosilicate | 009-014-00-1 | 247-278-1 | 25808-74-6 | |
Lead compounds with the exception of those specified elsewhere in this Annex | 082-001-00-6 | A, E | ||
Lead alkyls | 082-002-00-1 | A, E | ||
Lead azide | 082-003-00-7 | 236-542-1 | 13424-46-9 | |
Lead chromate | 082-004-00-2 | 231-846-0 | 7758-97-6 | |
Lead di(acetate) | 082-005-00-8 | 206-104-4 | 301-04-2 | |
Trilead bis(orthophosphate) | 082-006-00-3 | 231-205-5 | 7446-27-7 | |
Lead acetate | 082-007-00-9 | 215-630-3 | 1335-32-6 | |
Lead(II) methanesulphonate | 082-008-00-4 | 401-750-5 | 17570-76-2 | |
C.I. Pigment Yellow 34; (This substance is identified in the Colour Index by Colour Index Constitution No C.I. 77603.) | 082-009-00-X | 215-693-7 | 1344-37-2 | |
C.I. Pigment Red 104; (This substance is identified in the Colour Index by Colour Index Constitution No C.I. 77605.) | 082-010-00-5 | 235-759-9 | 12656-85-8 | |
Lead hydrogen arsenate | 082-011-00-0 | 232-064-2 | 7784-40-9 | |
1,2-Dibromo-3-chloropropane | 602-021-00-6 | 202-479-3 | 96-12-8 | |
2-bromopropane | 602-085-00-5 | 200-855-1 | 75-26-3 | E |
Warfarin; 4-hydroxy-3-(3-oxo-1-phenylbutyl)coumarin | 607-056-00-0 | 201-377-6 | 81-81-2 | |
Lead 2,4,6-trinitroresorcinoxide, lead styphnate | 609-019-00-4 | 239-290-0 | 15245-44-0 |
Appendix 6
Point 30 — Reproductive toxicants: category 1B (Table 3.1)/category 2 (Table 3.2)
Substances | Index No | EC No | CAS No | Notes |
Linuron (ISO) 3-(3,4-dichlorophenyl)-1-methoxy-1-methylurea | 006-021-00-1 | 206-356-5 | 330-55-2 | E |
6-(2-Chloroethyl)-6(2-methoxyethoxy)-2,5,7,10-tetraoxa-6-silaundecane; etacelasil | 014-014-00-X | 253-704-7 | 37894-46-5 | |
Flusilazole (ISO); bis(4-fluorophenyl)-(methyl)-(1H-1,2,4-triazol-1-ylmethyl)-silane | 014-017-00-6 | — | 85509-19-9 | E |
A mixture of: 4-[[bis-(4-fluorophenyl)-methylsilyl]methyl]-4H-1,2,4-triazole; 1-[[bis-(4-fluorophenyl)methyl-silyl]methyl]-1H-1,2,4-triazole | 014-019-00-7 | 403-250-2 | — | E |
Potassium dichromate | 024-002-00-6 | 231-906-6 | 7778-50-9 | E |
Ammonium dichromate | 024-003-00-1 | 232-143-1 | 7789-09-5 | E |
Sodium dichromate anhydrate | 024-004-00-7 | 234-190-3 | 10588-01-9 | E |
Sodium dichromate, dihydrate | 024-004-01-4 | 234-190-3 | 7789-12-0 | E |
Sodium chromate | 024-018-00-3 | 231-889-5 | 7775-11-3 | E |
Nickel tetracarbonyl | 028-001-00-1 | 236-669-2 | 13463-39-3 | |
Cadmium fluoride | 048-006-00-2 | 232-222-0 | 7790-79-6 | E |
Cadmium chloride | 048-008-00-3 | 233-296-7 | 10108-64-2 | E |
Cadmium sulphate | 048-009-00-9 | 233-331-6 | 10124-36-4 | E |
Benzo[a]pyrene; benzo[d,e,f]chrysene | 601-032-00-3 | 200-028-5 | 50-32-8 | |
1-Bromopropane Propyl bromide n-Propyl bromide | 602-019-00-5 | 203-445-0 | 106-94-5 | |
1,2,3-Trichloropropane | 602-062-00-X | 202-486-1 | 96-18-4 | D |
Diphenylether; octabromo derivate | 602-094-00-4 | 251-087-9 | 32536-52-0 | |
2-Methoxyethanol; ethylene glycol monomethyl ether; methylglycol | 603-011-00-4 | 203-713-7 | 109-86-4 | |
2-Ethoxyethanol; ethylene glycol monoethyl ether; ethylglycol | 603-012-00-X | 203-804-1 | 110-80-5 | |
1,2-Dimethoxyethane ethylene glycol dimethyl ether EGDME | 603-031-00-3 | 203-794-9 | 110-71-4 | |
2,3-Epoxypropan-1-ol; glycidol oxiranemethanol | 603-063-00-8 | 209-128-3 | 556-52-5 | E |
2-Methoxypropanol | 603-106-00-0 | 216-455-5 | 1589-47-5 | |
Bis(2-methoxyethyl) ether | 603-139-00-0 | 203-924-4 | 111-96-6 | |
R-2,3-epoxy-1-propanol | 603-143-002 | 404-660-4 | 57044-25-4 | E |
1,2-Bis(2-methoxyethoxy)ethane TEGDME; Triethylene glycol dimethyl ether; Triglyme | 603-176-00-2 | 203-977-3 | 112-49-2 | |
4,4'-isobutylethylidenediphenol; 2,2-bis (4'-hydroxyphenyl)-4-methylpentane | 604-024-00-8 | 401-720-1 | 6807-17-6 | |
Tetrahydrothiopyran-3-carboxaldehyde | 606-062-00-0 | 407-330-8 | 61571-06-0 | |
2-Methoxyethyl acetate; ethylene glycol monomethyl ether acetate; methylglycol acetate | 607-036-00-1 | 203-772-9 | 110-49-6 | |
2-Ethoxyethyl acetate; ethylene glycol monoethyl ether acetate; ethylglycol acetate | 607-037-00-7 | 203-839-2 | 111-15-9 | |
2-Ethylhexyl 3,5-bis(1,1-dimethylethyl)-4-hydroxyphenyl methyl thio acetate | 607-203-00-9 | 279-452-8 | 80387-97-9 | |
Bis(2-Methoxyethyl) phthalate | 607-228-00-5 | 204-212-6 | 117-82-8 | |
2-Methoxypropyl acetate | 607-251-00-0 | 274-724-2 | 70657-70-4 | |
Fluazifop-butyl (ISO); butyl (RS)-2-[4-(5-trifluoromethyl-2-pyridyloxy)phenoxy]propionate | 607-304-00-8 | 274-125-6 | 69806-50-4 | |
Vinclozolin (ISO); N-3,5-Dichlorophenyl-5-methyl-5-vinyl-1,3-oxazolidine-2,4-dione | 607-307-00-4 | 256-599-6 | 50471-44-8 | |
Methoxyacetic acid | 607-312-00-1 | 210-894-6 | 625-45-6 | E |
Bis(2-ethylhexyl) phthalate; di-(2-ethylhexyl) phthalate; DEHP | 607-317-00-9 | 204-211-0 | 117-81-7 | |
Dibutyl phthalate; DBP | 607-318-00-4 | 201-557-4 | 84-74-2 | |
(+/-) tetrahydrofurfuryl (R)-2-[4-(6-chloroquinoxalin-2-yloxy)phenyloxy]propionate | 607-373-00-4 | 414-200-4 | 119738-06-6 | E |
1,2-benzenedicarboxylic acid, dipentylester, branched and linear [1] n-pentyl-isopentylphthalate [2] di-n-pentyl phthalate [3] Diisopentylphthalate [4] | 607-426-00-1 | 284-032-2 [1]-[2] 205-017-9 [3]-[4] | 84777-06-0 [1]-[2] 131-18-0 [3] 42925-80-4 [4] | |
Benzyl butyl phthalate BBP | 607-430-00-3 | 201-622-7 | 85-68-7 | |
1,2-Benzenedicarboxylic acid di-C7-11-branched and linear alkylesters | 607-480-00-6 | 271-084-6 | 68515-42-4 | |
A mixture of: disodium 4-(3-ethoxycarbonyl-4-(5-(3-ethoxycarbonyl-5-hydroxy-1-(4-sulfonatophenyl)pyrazol-4-yl)penta-2,4-dienylidene)-4,5-dihydro-5-oxopyrazol-1-yl)benzenesulfonate; trisodium 4-(3-ethoxycarbonyl-4-(5-(3-ethoxycarbonyl-5-oxido-1-(4-sulfonatophenyl)pyrazol-4-yl)penta-2,4-dienylidene)-4,5-dihydro-5-oxopyrazol-1-yl)benzenesulfonate | 607-487-00-4 | 402-660-9 | — | |
Dinocap (ISO) | 609-023-00-6 | 254-408-0 | 39300-45-3 | E |
Binapacryl (ISO); 2-sec-butyl-4,6-dinitrophenyl-3-methylcrotonate | 609-024-00-1 | 207-612-9 | 485-31-4 | |
Dinoseb; 6-sec-butyl-2,4-dinitrophenol | 609-025-00-7 | 201-861-7 | 88-85-7 | |
Salts and esters of dinoseb, with the exception of those specified elsewhere in this Annex | 609-026-00-2 | |||
Dinoterb; 2-tert-butyl-4,6-dinitrophenol | 609-030-00-4 | 215-813-8 | 1420-07-1 | |
Salts and esters of dinoterb | 609-031-00-X | |||
Nitrofen (ISO); 2,4 dichlorophenyl 4-nitrophenyl ether | 609-040-00-9 | 217-406-0 | 1836-75-5 | |
Methyl-ONN-azoxymethyl acetate; methyl azoxy methyl acetate | 611-004-00-2 | 209-765-7 | 592-62-1 | |
2-[2-hydroxy-3-(2-chlorophenyl)carbamoyl-1-naphthylazo]-7-[2-hydroxy-3-(3-methylphenyl)carbamoyl-1-naphthylazo]fluoren-9-one | 611-131-00-3 | 420-580-2 | — | |
Azafenidin | 611-140-00-2 | — | 68049-83-2 | |
Tridemorph (ISO); 2,6-dimethyl-4-tridecylmorpholine | 613-020-00-5 | 246-347-3 | 24602-86-6 | |
Ethylene thiourea; imidazolidine-2-thione; 2-imidazoline-2-thiol | 613-039-00-9 | 202-506-9 | 96-45-7 | |
Carbendazim (ISO) methyl benzimidazol-2-ylcarbamate | 613-048-00-8 | 234-232-0 | 10605-21-7 | |
Benomyl (ISO) methyl 1-(butylcarbamoyl)benzimidazol-2-ylcarbamate | 613-049-00-3 | 241-775-7 | 17804-35-2 | |
Cycloheximide | 613-140-00-8 | 200-636-0 | 66-81-9 | |
Flumioxazin (ISO); N-(7-Fluoro-3,4-dihydro-3-oxo-4-prop-2-ynyl-2H-1,4-benzoxazin-6-yl)cyclohex-1-ene-1,2-dicarboxamide | 613-166-00-X | — | 103361-09-7 | |
(2RS,3RS)-3-(2-Chlorophenyl)-2-(4-fluorophenyl)-[(1H-1,2,4-triazol-1-yl)-methyl]oxirane | 613-175-00-9 | 406-850-2 | 106325-08-0 | |
3-Ethyl-2-methyl-2-(3-methylbutyl)-1,3-oxazolidine | 613-191-00-6 | 421-150-7 | 143860-04-2 | |
A mixture of: 1,3,5-tris(3-aminomethylphenyl)-1,3,5-(1H,3H,5H)-triazine-2,4,6-trione; a mixture of oligomers of 3,5-bis(3-aminomethylphenyl)-1-poly[3,5-bis(3-aminomethylphenyl)-2,4,6-trioxo-1,3,5-(1H,3H,5H)-triazin-1-yl]-1,3,5-(1H,3H,5H)-triazine-2,4,6-trione | 613-199-00-X | 421-550-1 | — | |
N, N-dimethylformamide; dimethyl formamide | 616-001-00-X | 200-679-5 | 68-12-2 | |
N, N-Dimethylacetamide | 616-011-00-4 | 204-826-4 | 127-19-5 | E |
Formamide | 616-052-00-8 | 200-842-0 | 75-12-7 | |
N-methylacetamide | 616-053-00-3 | 201-182-6 | 79-16-3 | |
N-methylformamide | 616-056-00-X | 204-624-6 | 123-39-7 | E |
Appendix 7
Special provisions on the labelling of articles containing asbestos
1. | All articles containing asbestos or the packaging thereof must bear the label defined as follows: (a) the label conforming to the specimen below shall be at least 5 cm high (H) and 2,5 cm wide; (b) it shall consist of two parts: — the top part (h1 = 40 % H) shall include the letter ‘a’ in white, on a black background, — the bottom part (h2= 60 % H) shall include the standard wording in white and/or black, on a red background, and shall be clearly legible; (c) if the article contains crocidolite, the words ‘contains asbestos’ used in the standard wording shall be replaced by ‘contains crocidolite/blue asbestos’. Member States may exclude from the provision of the first subparagraph articles intended to be placed on the market in their territory. The labelling of these articles must however bear the wording ‘contains asbestos’; (d) if labelling takes the form of direct printing on the articles, a single colour contrasting with the background colour is sufficient. h_1 = 40\% H, \quad h_2 = 60\% H |
2. | The label mentioned in this Appendix shall be affixed in accordance with the following rules: (a) on each of the smallest units supplied; (b) if an article has asbestos-based components, it is sufficient for these components only to bear the label. The labelling may be dispensed with if smallness of size or unsuitability of packaging make it impossible for a label to be affixed to the component. |
3. | Labelling of packaged articles containing asbestos 3.1. The following particulars shall appear on clearly legible and indelible labelling on the packaging of packaged articles containing asbestos: (a) the symbol and relevant indications of danger in accordance with this Annex; (b) safety instructions which must be selected in accordance with the particulars in this Annex, inasmuch as they are relevant for the particular article. Where additional safety information is provided on the packaging, this shall not weaken or contradict the particulars given in accordance with points (a) and (b). 3.2. Labelling in accordance with 3.1 shall be effected by means of: — a label firmly affixed to the packaging, or — a (tie-on) label securely attached to the package, or — direct printing of the packaging. 3.3. Articles containing asbestos and which are packaged only in loose plastic wrapping or the like shall be regarded as packaged articles and shall be labelled in accordance with 3.2. If articles are separated from such packages and placed on the market unpackaged, each of the smallest units supplied shall be accompanied by labelling particulars in accordance with 3.1. |
4. | Labelling of unpackaged articles containing asbestos For unpackaged articles containing asbestos, labelling in accordance with 3.1 shall be effected by means of: — a label firmly affixed to the article containing asbestos, — a (tie-on) label securely attached to such an article, — direct printing on the articles, or, if the abovementioned is not reasonably practicable as in the case of, for example, smallness of size of the article, the unsuitable nature of the article's properties or certain technical difficulties by means of a hand-out with labelling in accordance with 3.1. |
5. | Without prejudice to Community provisions on safety and hygiene at work, the label affixed to the article which may, in the context of its use, be processed or finished, shall be accompanied by any safety instructions which may be appropriate for the article concerned, and in particular by the following: — operate if possible out of doors or in a well-ventilated place, — preferably use hand tools or low-speed tools equipped, if necessary, with an appropriate dust-extraction facility. If high-speed tools are used, they should always be equipped with such a facility, — if possible, dampen before cutting or drilling, — dampen dust and place it in a properly closed receptacle and dispose of it safely. |
6. | The labelling of any article intended for domestic use which is not covered by Section 5 and which is likely, during use, to release asbestos fibres shall, if necessary, contain the following safety instruction: ‘replace when worn’. |
7. | The labelling of articles containing asbestos shall be in the official language or languages of the Member State(s) where the article is placed on the market. |
Appendix 8
Point 43 — Azocolourants
List of aromatic amines
CAS No | Index No | EC No | Substances | |
1. | 92-67-1 | 612-072-00-6 | 202-177-1 | biphenyl-4-ylamine 4-aminobiphenyl xenylamine |
2. | 92-87-5 | 612-042-00-2 | 202-199-1 | benzidine |
3. | 95-69-2 | 202-441-6 | 4-chloro-o-toluidine | |
4. | 91-59-8 | 612-022-00-3 | 202-080-4 | 2-naphthylamine |
5. | 97-56-3 | 611-006-00-3 | 202-591-2 | o-aminoazotoluene 4-amino-2',3-dimethylazobenzene 4-o-tolylazo-o-toluidine |
6. | 99-55-8 | 202-765-8 | 5-nitro-o-toluidine | |
7. | 106-47-8 | 612-137-00-9 | 203-401-0 | 4-chloroaniline |
8. | 615-05-4 | 210-406-1 | 4-methoxy-m-phenylenediamine | |
9. | 101-77-9 | 612-051-00-1 | 202-974-4 | 4,4'-methylenedianiline 4,4'-diaminodiphenylmethane |
10. | 91-94-1 | 612-068-00-4 | 202-109-0 | 3,3'-dichlorobenzidine 3,3'-dichlorobiphenyl-4,4'-ylenediamine |
11. | 119-90-4 | 612-036-00-X | 204-355-4 | 3,3'-dimethoxybenzidine o-dianisidine |
12. | 119-93-7 | 612-041-00-7 | 204-358-0 | 3,3'-dimethylbenzidine 4,4'-bi-o-toluidine |
13. | 838-88-0 | 612-085-00-7 | 212-658-8 | 4,4'-methylenedi-o-toluidine |
14. | 120-71-8 | 204-419-1 | 6-methoxy-m-toluidine p-cresidine | |
15. | 101-14-4 | 612-078-00-9 | 202-918-9 | 4,4'-methylene-bis-(2-chloro-aniline) 2,2'-dichloro-4,4'-methylene-dianiline |
16. | 101-80-4 | 202-977-0 | 4,4'-oxydianiline | |
17. | 139-65-1 | 205-370-9 | 4,4'-thiodianiline | |
18. | 95-53-4 | 612-091-00-X | 202-429-0 | o-toluidine 2-aminotoluene |
19. | 95-80-7 | 612-099-00-3 | 202-453-1 | 4-methyl-m-phenylenediamine |
20. | 137-17-7 | 205-282-0 | 2,4,5-trimethylaniline | |
21. | 90-04-0 | 612-035-00-4 | 201-963-1 | o-anisidine 2-methoxyaniline |
22. | 60-09-3 | 611-008-00-4 | 200-453-6 | 4-amino azobenzene |
Appendix 9
Point 43 — Azocolourants
List of azodyes
CAS No | Index No | EC No | Substances | |
1. | Not allocated Component 1: CAS-No: 118685-33-9 C39H23ClCrN7O12S.2Na Component 2: C46H30CrN10O20S2.3Na | 611-070-00-2 | 405-665-4 | A mixture of: disodium (6-(4-anisidino)-3-sulfonato-2-(3,5-dinitro-2-oxidophenylazo)-1-naphtholato)(1-(5-chloro-2-oxidophenylazo)-2-naphtholato)chromate(1-); trisodium bis(6-(4-anisidino)-3-sulfonato-2-(3,5-dinitro-2-oxidophenylazo)-1-naphtholato)chromate(1-) |
Appendix 10
Point 43 — Azocolourants
List of testing methods
European standardisation organisation (1) | Reference and title of the standard | Reference document | Reference of the superseded standard |
CEN | Leather — Chemical tests — Determination of certain azocolorants in dyed leathers | CEN ISO/TS 17234:2003 | NONE |
CEN | Textiles — Methods for the determination of certain aromatic amines derived from azocolorants — Part 1: Detection of the use of certain azo colorants accessible without extraction | EN 14362-1:2003 | NONE |
CEN | Textiles — Methods for determination of certain aromatic amines derived from azocolorants — Part 2: Detection of the use of certain azo colorants accessible by extracting the fibres | EN 14362-2:2003 | NONE |
(1) ESO: European standardisation organisations: CEN: rue de Stassart 36, B-1050 Bruxelles; tel. (32-2) 550 08 11, fax (32-2) 550 08 19. http://www.cenorm.be CENELEC: rue de Stassart 36, B-1050 Bruxelles; tel. (32-2) 519 68 71, fax (32-2) 519 69 19. http://www.cenelec.org ETSI: 650, route des Lucioles, F-06921 Sophia Antipolis; tel. (33) 492 94 42 00, fax (33) 493 65 47 16. http://www.etsi.org | |||