Annex XVII - RESTRICTIONS ON THE MANUFACTURE, PLACING ON THE MARKET AND USE OF CERTAIN DANGEROUS SUBSTANCES, MIXTURES AND ARTICLES

Column 1 Designation of the substance, of the group of substances or of the mixture

Column 2 Conditions of restriction

1. Polychlorinated terphenyls (PCTs)

Shall not be placed on the market, or used: — as substances, — in mixtures, including waste oils, or in equipment, in concentrations greater than 50 mg/kg (0,005 % by weight).

2. Chloroethene (vinyl chloride) CAS No 75-01-4 EC No 200-831-0

Shall not be used as propellant in aerosols for any use. Aerosols dispensers containing the substance as propellant shall not be placed on the market.

►M3 3. Liquid substances or mixtures which are regarded as dangerous in accordance with Directive 1999/45/EC or are fulfilling the criteria for any of the following hazard classes or categories set out in Annex I to Regulation (EC) No 1272/2008: (a) hazard classes 2.1 to 2.4, 2.6 and 2.7, 2.8 types A and B, 2.9, 2.10, 2.12, 2.13 categories 1 and 2, 2.14 categories 1 and 2, 2.15 types A to F; (b) hazard classes 3.1 to 3.6, 3.7 adverse effects on sexual function and fertility or on development, 3.8 effects other than narcotic effects, 3.9 and 3.10; (c) hazard class 4.1; (d) hazard class 5.1. ◄

1. Shall not be used in: — ornamental articles intended to produce light or colour effects by means of different phases, for example in ornamental lamps and ashtrays, — tricks and jokes, — games for one or more participants, or any article intended to be used as such, even with ornamental aspects, 2. Articles not complying with paragraph 1 shall not be placed on the market. 3. Shall not be placed on the market if they contain a colouring agent, unless required for fiscal reasons, or perfume, or both, if they: — can be used as fuel in decorative oil lamps for supply to the general public, and, — present an aspiration hazard and are labelled with R65 or H304, 4. Decorative oil lamps for supply to the general public shall not be placed on the market unless they conform to the European Standard on Decorative oil lamps (EN 14059) adopted by the European Committee for Standardisation (CEN). 5. Without prejudice to the implementation of other Community provisions relating to the classification, packaging and labelling of dangerous substances and mixtures, suppliers shall ensure, before the placing on the market, that the following requirements are met: (a) lamp oils, labelled with R65 or H304, intended for supply to the general public are visibly, legibly and indelibly marked as follows: ‘Keep lamps filled with this liquid out of the reach of children’; and, by 1 December 2010, ‘Just a sip of lamp oil — or even sucking the wick of lamps — may lead to life-threatening lung damage’; (b) grill lighter fluids, labelled with R65 or H304, intended for supply to the general public are legibly and indelibly marked by 1 December 2010 as follows: ‘Just a sip of grill lighter may lead to life threatening lung damage’; (c) lamp oils and grill lighters, labelled with R65 or H304, intended for supply to the general public are packaged in black opaque containers not exceeding 1 litre by 1 December 2010. 6. No later than 1 June 2014, the Commission shall request the European Chemicals Agency to prepare a dossier, in accordance with Article 69 of the present Regulation with a view to ban, if appropriate, grill lighter fluids and fuel for decorative lamps, labelled R65 or H304, intended for supply to the general public. 7. Natural or legal persons placing on the market for the first time lamp oils and grill lighter fluids, labelled with R65 or H304, shall by 1 December 2011, and annually thereafter, provide data on alternatives to lamp oils and grill lighter fluids labelled R65 or H304 to the competent authority in the Member State concerned. Member States shall make those data available to the Commission.

4. Tris (2,3 dibromopropyl) phosphate CAS No 126-72-7

1. Shall not be used in textile articles, such as garments, undergarments and linen, intended to come into contact with the skin. 2. Articles not complying with paragraph 1 shall not be placed on the market.

5. Benzene CAS No 71-43-2 EC No 200-753-7

1. Shall not be used in toys or parts of toys where the concentration of benzene in the free state is greater than 5 mg/kg (0,0005 %) of the weight of the toy or part of toy. 2. Toys and parts of toys not complying with paragraph 1 shall not be placed on the market. 3. Shall not be placed on the market, or used, — as a substance, — as a constituent of other substances, or in mixtures, in concentrations equal to, or greater than 0,1 % by weight. 4. However, paragraph 3 shall not apply to: (a) motor fuels which are covered by Directive 98/70/EC; (b) substances and mixtures for use in industrial processes not allowing for the emission of benzene in quantities in excess of those laid down in existing legislation.

6. Asbestos fibres (a) Crocidolite CAS No 12001-28-4 (b) Amosite CAS No 12172-73-5 (c) Anthophyllite CAS No 77536-67-5 (d) Actinolite CAS No 77536-66-4 (e) Tremolite CAS No 77536-68-6 (f) Chrysotile CAS No 12001-29-5 CAS No 132207-32-0

1. The manufacture, placing on the market and use of these fibres and of articles containing these fibres added intentionally is prohibited. However, Member States may exempt the placing on the market and use of diaphragms containing chrysotile (point (f)) for existing electrolysis installations until they reach the end of their service life, or until suitable asbestos-free substitutes become available, whichever is the sooner. By 1 June 2011 Member States making use of this exemption shall provide a report to the Commission on the availability of asbestos free substitutes for electrolysis installations and the efforts undertaken to develop such alternatives, on the protection of the health of workers in the installations, on the source and quantities of chrysotile, on the source and quantities of diaphragms containing chrysotile, and the envisaged date of the end of the exemption. The Commission shall make this information publicly available. Following receipt of those reports, the Commission shall request the Agency to prepare a dossier in accordance with Article 69 with a view to prohibit the placing on the market and use of diaphragms containing chrysotile. 2. The use of articles containing asbestos fibres referred to in paragraph 1 which were already installed and/or in service before 1 January 2005 shall continue to be permitted until they are disposed of or reach the end of their service life. However, Member States may, for reasons of protection of human health, restrict, prohibit or make subject to specific conditions, the use of such articles before they are disposed of or reach the end of their service life. Member States may allow placing on the market of articles in their entirety containing asbestos fibres referred to in paragraph 1 which were already installed and/or in service before 1 January 2005, under specific conditions ensuring a high level of protection of human health. Member States shall communicate these national measures to the Commission by 1 June 2011. The Commission shall make this information publicly available. 3. Without prejudice to the application of other Community provisions on the classification, packaging and labelling of substances and mixtures, the placing on the market and use of articles containing these fibres, as permitted according to the preceding derogations, shall be permitted only if suppliers ensure before the placing on the market that articles bear a label in accordance with Appendix 7 to this Annex.

7. Tris(aziridinyl)phosphinoxide CAS No 545-55-1 EC No 208-892-5

1. Shall not be used in textile articles, such as garments, undergarments and linen, intended to come into contact with the skin. 2. Articles not complying with paragraph 1 shall not be placed on the market.

8. Polybromobiphenyls; Polybrominatedbiphenyls (PBB) CAS No 59536-65-1

1. Shall not be used in textile articles, such as garments, undergarments and linen, intended to come into contact with the skin. 2. Articles not complying with paragraph 1 shall not be placed on the market.

9. (a) Soap bark powder (Quillaja saponaria) and its derivatives containing saponines CAS No 68990-67-0 EC 273-620-4 (b) Powder of the roots of Helleborus viridis and Helleborus niger (c) Powder of the roots of Veratrum album and Veratrum nigrum (d) Benzidine and/or its derivatives CAS No 92-87-5 EC No 202-199-1 (e) o-Nitrobenzaldehyde CAS No 552-89-6 EC No 209-025-3 (f) Wood powder

1. Shall not be used, in jokes and hoaxes or in mixtures or articles intended to be used as such, for instance as a constituent of sneezing powder and stink bombs. 2. Jokes and hoaxes, or mixtures or articles intended to be used as such, not complying with paragraph 1 shall not be placed on the market. 3. However, paragraphs 1 and 2 shall not apply to stink bombs containing not more than 1,5 ml of liquid.

10. (a) Ammonium sulphide CAS No 12135-76-1 EC No 235-223-4 (b) Ammonium hydrogen sulphide CAS No 12124-99-1 EC No 235-184-3 (c) Ammonium polysulphide CAS No 9080-17-5 EC No 232-989-1

1. Shall not be used, in jokes and hoaxes or in mixtures or articles intended to be used as such, for instance as a constituent of sneezing powder and stink bombs. 2. Jokes and hoaxes, or mixtures or articles intended to be used as such, not complying with paragraph 1 shall not be placed on the market. 3. However, paragraphs 1 and 2 shall not apply to stink bombs containing not more than 1,5 ml of liquid.

11. Volatile esters of bromoacetic acids: (a) Methyl bromoacetate CAS No 96-32-2 EC No 202-499-2 (b) Ethyl bromoacetate CAS No 105-36-2 EC No 203-290-9 (c) Propyl bromoacetate CAS No 35223-80-4 (d) Butyl bromoacetate CAS No 18991-98-5 EC No 242-729-9

1. Shall not be used, in jokes and hoaxes or in mixtures or articles intended to be used as such, for instance as a constituent of sneezing powder and stink bombs. 2. Jokes and hoaxes, or mixtures or articles intended to be used as such, not complying with paragraph 1 shall not be placed on the market. 3. However, paragraphs 1 and 2 shall not apply to stink bombs containing not more than 1,5 ml of liquid.

12. 2-Naphthylamine CAS No 91-59-8 EC No 202-080-4 and its salts 13. Benzidine CAS No 92-87-5 EC No 202-199-1 and its salts 14. 4-Nitrobiphenyl CAS No 92-93-3 Einecs EC No 202-204-7 15. 4-Aminobiphenyl xenylamine CAS No 92-67-1 Einecs EC No 202-177-1 and its salts

The following shall apply to entries 12 to 15: Shall not be placed on the market, or used, as substances or in mixtures in concentrations greater than 0,1 % by weight.

16. Lead carbonates: (a) Neutral anhydrous carbonate (PbCO₃) CAS No 598-63-0 EC No 209-943-4 (b) Trilead-bis(carbonate)-dihydroxide 2Pb CO₃-Pb(OH)₂ CAS No 1319-46-6 EC No 215-290-6

Shall not be placed on the market, or used, as substances or in mixtures, where the substance or mixture is intended for use as paint. However, Member States may, in accordance with the provisions of International Labour Organisation (ILO) Convention 13 on the use of white lead and sulphates of lead in paint, permit the use on their territory of the substance or mixture for the restoration and maintenance of works of art and historic buildings and their interiors.

17. Lead sulphates: (a) PbSO₄ CAS No 7446-14-2 EC No 231-198-9 (b) Pb_x SO₄ CAS No 15739-80-7 EC No 239-831-0

Shall not be placed on the market, or used, as substances or in mixtures, where the substance or mixture is intended for use as paint. However, Member States may, in accordance with the provisions of ILO Convention 13 on the use of white lead and sulphates of lead in paint, permit the use on their territory of the substance or mixture for the restoration and maintenance of works of art and historic buildings and their interiors.

18. Mercury compounds

Shall not be placed on the market, or used, as substances or in mixtures where the substance or mixture is intended for use: (a) to prevent the fouling by micro-organisms, plants or animals of: — the hulls of boats, — cages, floats, nets and any other appliances or equipment used for fish or shellfish farming, — any totally or partly submerged appliances or equipment; (b) in the preservation of wood; (c) in the impregnation of heavy-duty industrial textiles and yarn intended for their manufacture; (d) in the treatment of industrial waters, irrespective of their use.

18a. Mercury CAS No 7439-97-6 EC No 231-106-7

1. Shall not be placed on the market: (a) in fever thermometers; (b) in other measuring devices intended for sale to the general public (such as manometers, barometers, sphygmomanometers, thermometers other than fever thermometers). 2. The restriction in paragraph 1 shall not apply to measuring devices that were in use in the Community before 3 April 2009. However Member States may restrict or prohibit the placing on the market of such measuring devices. 3. The restriction in paragraph 1(b) shall not apply to: (a) measuring devices more than 50 years old on 3 October 2007; (b) barometers (except barometers within point (a)) until 3 October 2009. 4. By 3 October 2009 the Commission shall carry out a review of the availability of reliable safer alternatives that are technically and economically feasible for mercury containing sphygmomanometers and other measuring devices in healthcare and in other professional and industrial uses. On the basis of this review or as soon as new information on reliable safer alternatives for sphygmomanometers and other measuring devices containing mercury becomes available, the Commission shall, if appropriate, present a legislative proposal to extend the restrictions in paragraph 1 to sphygmomanometers and other measuring devices in healthcare and in other professional and industrial uses, so that mercury in measuring devices is phased out whenever technically and economically feasible.

19. Arsenic compounds

1. Shall not be placed on the market, or used, as substances or in mixtures where the substance or mixture is intended for use to prevent the fouling by micro-organisms, plants or animals of: — the hulls of boats, — cages, floats, nets and any other appliances or equipment used for fish or shellfish farming, — any totally or partly submerged appliances or equipment. 2. Shall not be placed on the market, or used, as substances or in mixtures where the substance or mixture is intended for use in the treatment of industrial waters, irrespective of their use. 3. Shall not be used in the preservation of wood. Furthermore, wood so treated shall not be placed on the market. 4. By way of derogation from paragraph 3: (a) Relating to the substances and mixtures for the preservation of wood: these may only be used in industrial installations using vacuum or pressure to impregnate wood if they are solutions of inorganic compounds of the copper, chromium, arsenic (CCA) type C and if they are authorised in accordance with Article 5(1) of Directive 98/8/EC. Wood so treated shall not be placed on the market before fixation of the preservative is completed. (b) Wood treated with CCA solution in accordance with point (a) may be placed on the market for professional and industrial use provided that the structural integrity of the wood is required for human or livestock safety and skin contact by the general public during its service life is unlikely: — as structural timber in public and agricultural buildings, office buildings, and industrial premises, — in bridges and bridgework, — as constructional timber in freshwater areas and brackish waters, for example jetties and bridges, — as noise barriers, — in avalanche control, — in highway safety fencing and barriers, — as debarked round conifer livestock fence posts, — in earth retaining structures, — as electric power transmission and telecommunications poles, — as underground railway sleepers. (c) Without prejudice to the application of other Community provisions on the classification, packaging and labelling of substances and mixtures, suppliers shall ensure before the placing on the market that all treated wood placed on the market is individually labelled ‘For professional and industrial installation and use only, contains arsenic’. In addition, all wood placed on the market in packs shall also bear a label stating ‘Wear gloves when handling this wood. Wear a dust mask and eye protection when cutting or otherwise crafting this wood. Waste from this wood shall be treated as hazardous by an authorised undertaking’. (d) Treated wood referred to under point (a) shall not be used: — in residential or domestic constructions, whatever the purpose, — in any application where there is a risk of repeated skin contact, — in marine waters, — for agricultural purposes other than for livestock fence posts and structural uses in accordance with point (b), — in any application where the treated wood may come into contact with intermediate or finished products intended for human and/or animal consumption. 5. Wood treated with arsenic compounds that was in use in the Community before 30 September 2007, or that was placed on the market in accordance with paragraph 4 may remain in place and continue to be used until it reaches the end of its service life. 6. Wood treated with CCA type C that was in use in the Community before 30 September 2007, or that was placed on the market in accordance with paragraph 4: — may be used or reused subject to the conditions pertaining to its use listed under points 4(b), (c) and (d), — may be placed on the market subject to the conditions pertaining to its use listed under points 4(b), (c) and (d). 7. Member States may allow wood treated with other types of CCA solutions that was in use in the Community before 30 September 2007: — to be used or reused subject to the conditions pertaining to its use listed under points 4 (b), (c) and (d), — to be placed on the market subject to the conditions pertaining to its use listed under points 4(b), (c) and (d).

20. Organostannic compounds

1. Shall not be placed on the market, or used, as substances or in mixtures where the substance or mixture is acting as biocide in free association paint. 2. Shall not be placed on the market, or used, as substances or in mixtures where the substance or mixture acts as biocide to prevent the fouling by micro-organisms, plants or animals of: (a) all craft irrespective of their length intended for use in marine, coastal, estuarine and inland waterways and lakes; (b) cages, floats, nets and any other appliances or equipment used for fish or shellfish farming; (c) any totally or partly submerged appliance or equipment. 3. Shall not be placed on the market, or used, as substances or in mixtures where the substance or mixture is intended for use in the treatment of industrial waters. ►M6 4. Tri-substituted organostannic compounds: (a) Tri-substituted organostannic compounds such as tributyltin (TBT) compounds and triphenyltin (TPT) compounds shall not be used after 1 July 2010 in articles where the concentration in the article, or part thereof, is greater than the equivalent of 0,1 % by weight of tin. (b) Articles not complying with point (a) shall not be placed on the market after 1 July 2010, except for articles that were already in use in the Community before that date. 5. Dibutyltin (DBT) compounds: (a) Dibutyltin (DBT) compounds shall not be used after 1 January 2012 in mixtures and articles for supply to the general public where the concentration in the mixture or the article, or part thereof, is greater than the equivalent of 0,1 % by weight of tin. (b) Articles and mixtures not complying with point (a) shall not be placed on the market after 1 January 2012, except for articles that were already in use in the Community before that date. (c) By way of derogation, points (a) and (b) shall not apply until 1 January 2015 to the following articles and mixtures for supply to the general public: — one-component and two-component room temperature vulcanisation sealants (RTV-1 and RTV-2 sealants) and adhesives, — paints and coatings containing DBT compounds as catalysts when applied on articles, — soft polyvinyl chloride (PVC) profiles whether by themselves or coextruded with hard PVC, — fabrics coated with PVC containing DBT compounds as stabilisers when intended for outdoor applications, — outdoor rainwater pipes, gutters and fittings, as well as covering material for roofing and façades, (d) By way of derogation, points (a) and (b) shall not apply to materials and articles regulated under Regulation (EC) No 1935/2004. 6. Dioctyltin (DOT) compound: (a) Dioctyltin (DOT) compounds shall not be used after 1 January 2012 in the following articles for supply to, or use by, the general public, where the concentration in the article, or part thereof, is greater than the equivalent of 0,1 % by weight of tin: — textile articles intended to come into contact with the skin, — gloves, — footwear or part of footwear intended to come into contact with the skin, — wall and floor coverings, — childcare articles, — female hygiene products, — nappies, — two-component room temperature vulcanisation moulding kits (RTV-2 moulding kits). (b) Articles not complying with point (a) shall not be placed on the market after 1 January 2012, except for articles that were already in use in the Community before that date. ◄

21. Di-μ-oxo-di-n-butylstanniohydroxyborane/Dibutyltin hydrogen borate C₈H₁₉BO₃Sn (DBB) CAS No 75113-37-0 EC No 401-040-5

Shall not be placed on the market, or used, as a substance, or in mixtures in a concentration equal to, or greater than 0,1 % by weight. However, the first paragraph shall not apply to this substance (DBB) or mixtures containing it if these are intended solely for conversion into articles, among which this substance will no longer feature in a concentration equal to or greater than 0,1 %.

22. Pentachlorophenol CAS No 87-86-5 EC No 201-778-6 and its salts and esters

Shall not be placed on the market, or used, — as a substance, — as a constituent in other substances, or in mixtures, in a concentration equal to or greater than 0,1 % by weight.

23. Cadmium CAS No 7440-43-9 EC No 231-152-8 and its compounds

For the purpose of this entry, the codes and chapters indicated in square brackets are the codes and chapters of the tariff and statistical nomenclature of Common Customs Tariff as established by Council Regulation (EEC) No 2658/87 (¹). ►M13 1. Shall not be used in mixtures and articles produced from synthetic organic polymers (hereafter referred to as plastic material) such as: — polymers or copolymers of vinyl chloride (PVC) [3904 10] [3904 21] — polyurethane (PUR) [3909 50] — low-density polyethylene (LDPE), with the exception of low-density polyethylene used for the production of coloured masterbatch [3901 10] — cellulose acetate (CA) [3912 11] — cellulose acetate butyrate (CAB) [3912 11] — epoxy resins [3907 30] — melamine-formaldehyde (MF) resins [3909 20] — urea-formaldehyde (UF) resins [3909 10] — unsaturated polyesters (UP) [3907 91] — polyethylene terephthalate (PET) [3907 60] — polybutylene terephthalate (PBT) — transparent/general-purpose polystyrene [3903 11] — acrylonitrile methylmethacrylate (AMMA) — cross-linked polyethylene (VPE) — high-impact polystyrene — polypropylene (PP) [3902 10] — high-density polyethylene (HDPE) [3901 20] — acrylonitrile butadiene styrene (ABS) [3903 30] — poly(methyl methacrylate) (PMMA) [3906 10]. Mixtures and articles produced from plastic material shall not be placed on the market if the concentration of cadmium (expressed as Cd metal) is equal to or greater than 0,01 % by weight of the plastic material. By way of derogation, the second subparagraph shall not apply to articles placed on the market before 10 December 2011. The first and second subparagraphs apply without prejudice to Council Directive 94/62/EC (¹³) and acts adopted on its basis. 2. Shall not be used in paints [3208] [3209]. For paints with a zinc content exceeding 10 % by weight of the paint, the concentration of cadmium (expressed as Cd metal) shall not be equal to or greater than 0,1 % by weight. Painted articles shall not be placed on the market if the concentration of cadmium (expressed as Cd metal) is equal to or greater than 0,1 % by weight of the paint on the painted article. 3. By way of derogation, paragraphs 1 and 2 shall not apply to articles coloured with mixtures containing cadmium for safety reasons. 4. By way of derogation, paragraph 1, second subparagraph shall not apply to: — mixtures produced from PVC waste, hereinafter referred to as ‘recovered PVC’, — mixtures and articles containing recovered PVC if their concentration of cadmium (expressed as Cd metal) does not exceed 0,1 % by weight of the plastic material in the following rigid PVC applications: — (a) profiles and rigid sheets for building applications; (b) doors, windows, shutters, walls, blinds, fences, and roof gutters; (c) decks and terraces; (d) cable ducts; (e) pipes for non-drinking water if the recovered PVC is used in the middle layer of a multilayer pipe and is entirely covered with a layer of newly produced PVC in compliance with paragraph 1 above. Suppliers shall ensure, before the placing on the market of mixtures and articles containing recovered PVC for the first time, that these are visibly, legibly and indelibly marked as follows: ‘Contains recovered PVC’ or with the following pictogram: \mathrm{PVC} In accordance with Article 69 of this Regulation, the derogation granted in paragraph 4 will be reviewed, in particular with a view to reducing the limit value for cadmium and to reassess the derogation for the applications listed in points (a) to (e), by 31 December 2017. ◄ 5. For the purpose of this entry, ‘cadmium plating’ means any deposit or coating of metallic cadmium on a metallic surface. Shall not be used for cadmium plating metallic articles or components of the articles used in the following sectors/applications: (a) equipment and machinery for: — food production [8210] [8417 20] [8419 81] [8421 11] [8421 22] [8422] [8435] [8437] [8438] [8476 11] — agriculture [8419 31] [8424 81] [8432] [8433] [8434] [8436] — cooling and freezing [8418] — printing and book-binding [8440] [8442] [8443] (b) equipment and machinery for the production of: — household goods [7321] [8421 12] [8450] [8509] [8516] — furniture [8465] [8466] [9401] [9402] [9403] [9404] — sanitary ware [7324] — central heating and air conditioning plant [7322] [8403] [8404] [8415] In any case, whatever their use or intended final purpose, the placing on the market of cadmium-plated articles or components of such articles used in the sectors/applications listed in points (a) and (b) above and of articles manufactured in the sectors listed in point (b) above is prohibited. 6. The provisions referred to in paragraph 5 shall also be applicable to cadmium-plated articles or components of such articles when used in the sectors/applications listed in points (a) and (b) below and to articles manufactured in the sectors listed in (b) below: (a) equipment and machinery for the production of: — paper and board [8419 32] [8439] [8441] textiles and clothing [8444] [8445] [8447] [8448] [8449] [8451] [8452] (b) equipment and machinery for the production of: — industrial handling equipment and machinery [8425] [8426] [8427] [8428] [8429] [8430] [8431] — road and agricultural vehicles [chapter 87] — rolling stock [chapter 86] — vessels [chapter 89] 7. However, the restrictions in paragraphs 5 and 6 shall not apply to: — articles and components of the articles used in the aeronautical, aerospace, mining, offshore and nuclear sectors whose applications require high safety standards and in safety devices in road and agricultural vehicles, rolling stock and vessels, — electrical contacts in any sector of use, where that is necessary to ensure the reliability required of the apparatus on which they are installed. ►M13 8. Shall not be used in brazing fillers in concentration equal to or greater than 0,01 % by weight. Brazing fillers shall not be placed on the market if the concentration of cadmium (expressed as Cd metal) is equal to or greater than 0,01 % by weight. For the purpose of this paragraph brazing shall mean a joining technique using alloys and undertaken at temperatures above 450 °C. 9. By way of derogation, paragraph 8 shall not apply to brazing fillers used in defence and aerospace applications and to brazing fillers used for safety reasons. 10. Shall not be used or placed on the market if the concentration is equal to or greater than 0,01 % by weight of the metal in: (i) metal beads and other metal components for jewellery making; (ii) metal parts of jewellery and imitation jewellery articles and hair accessories, including: — bracelets, necklaces and rings, — piercing jewellery, — wrist-watches and wrist-wear, — brooches and cufflinks. ►C5 11. By way of derogation, paragraph 10 shall not apply to articles placed on the market before 10 December 2011 and jewellery more than 50 years old on 10 December 2011. ◄ ◄

24. Monomethyl — tetrachlorodiphenyl methane Trade name: Ugilec 141 CAS No 76253-60-6

1. Shall not be placed on the market, or used, as a substance or in mixtures. Articles containing the substance shall not be placed on the market. 2. By way of derogation, paragraph 1 shall not apply: (a) in the case of plant and machinery already in service on 18 June 1994, until such plant and machinery is disposed of; (b) in the case of the maintenance of plant and machinery already in service within a Member State on 18 June 1994. For the purposes of point (a) Member States may, on grounds of human health protection and environmental protection, prohibit within their territory the use of such plant or machinery before it is disposed of.

25. Monomethyl-dichloro-diphenyl methane Trade name: Ugilec 121 Ugilec 21

Shall not be placed on the market, or used, as a substance or in mixtures. Articles containing the substance shall not be placed on the market.

26. Monomethyl-dibromo-diphenyl methane bromobenzylbromotoluene, mixture of isomers Trade name: DBBT CAS No 99688-47-8

Shall not be placed on the market, or used, as a substance or in mixtures. Articles containing the substance shall not be placed on the market.

27. Nickel CAS No 7440-02-0 EC No 231-111-4 and its compounds

1. Shall not be used: (a) in any post assemblies which are inserted into pierced ears and other pierced parts of the human body unless the rate of nickel release from such post assemblies is less than 0,2 μg/cm²/week (migration limit); (b) in articles intended to come into direct and prolonged contact with the skin such as: — earrings, — necklaces, bracelets and chains, anklets, finger rings, — wrist-watch cases, watch straps and tighteners, — rivet buttons, tighteners, rivets, zippers and metal marks, when these are used in garments, if the rate of nickel release from the parts of these articles coming into direct and prolonged contact with the skin is greater than 0,5 μg/cm²/week. (c) in articles referred to in point (b) where these have a non-nickel coating unless such coating is sufficient to ensure that the rate of nickel release from those parts of such articles coming into direct and prolonged contact with the skin will not exceed 0,5 μg/cm²/week for a period of at least two years of normal use of the article. 2. Articles which are the subject of paragraph 1 shall not be placed on the market unless they conform to the requirements set out in that paragraph. 3. The standards adopted by the European Committee for Standardisation (CEN) shall be used as the test methods for demonstrating the conformity of articles to paragraphs 1 and 2.

28. Substances which appear in Part 3 of Annex VI to Regulation (EC) No 1272/2008 classified as carcinogen category 1A or 1B (Table 3.1) or carcinogen category 1 or 2 (Table 3.2) and listed as follows: — Carcinogen category 1A (Table 3.1)/carcinogen category 1 (Table 3.2) listed in Appendix 1 — Carcinogen category 1B (Table 3.1)/carcinogen category 2 (Table 3.2) listed in Appendix 2 29. Substances which appear in Part 3 of Annex VI to Regulation (EC) No 1272/2008 classified as germ cell mutagen category 1A or 1B (Table 3.1) or mutagen category 1 or 2 (Table 3.2) and listed as follows: — Mutagen category 1A (Table 3.1)/mutagen category 1 (Table 3.2) listed in Appendix 3 — Mutagen category 1B (Table 3.1)/mutagen category 2 (Table 3.2) listed in Appendix 4 30. Substances which appear in Part 3 of Annex VI to Regulation (EC) No 1272/2008 classified as toxic to reproduction category 1A or 1B (Table 3.1) or toxic to reproduction category 1 or 2 (Table 3.2) and listed as follows: — Reproductive toxicant category 1A adverse effects on sexual function and fertility or on development (Table 3.1) or reproductive toxicant category 1 with R60 (May impair fertility) or R61 (May cause harm to the unborn child) (Table 3.2) listed in Appendix 5 — Reproductive toxicant category 1B adverse effects on sexual function and fertility or on development (Table 3.1) or reproductive toxicant category 2 with R60 (May impair fertility) or R61 (May cause harm to the unborn child) (Table 3.2) listed in Appendix 6

Without prejudice to the other parts of this Annex the following shall apply to entries 28 to 30: 1. Shall not be placed on the market, or used, — as substances, — as constituents of other substances, or, — in mixtures, for supply to the general public when the individual concentration in the substance or mixture is equal to or greater than: — either the relevant specific concentration limit specified in Part 3 of Annex VI to Regulation (EC) No 1272/2008, or, — the relevant concentration specified in Directive 1999/45/EC. Without prejudice to the implementation of other Community provisions relating to the classification, packaging and labelling of substances and mixtures, suppliers shall ensure before the placing on the market that the packaging of such substances and mixtures is marked visibly, legibly and indelibly as follows: ‘Restricted to professional users’. 2. By way of derogation, paragraph 1 shall not apply to: (a) medicinal or veterinary products as defined by Directive 2001/82/EC and Directive 2001/83/EC; (b) cosmetic products as defined by Directive 76/768/EEC; (c) the following fuels and oil products: — motor fuels which are covered by Directive 98/70/EC, — mineral oil products intended for use as fuel in mobile or fixed combustion plants, — fuels sold in closed systems (e.g. liquid gas bottles); (d) artists’ paints covered by Directive 1999/45/EC; ►M14 (e) the substances listed in Appendix 11, column 1, for the applications or uses listed in Appendix 11, column 2. Where a date is specified in column 2 of Appendix 11, the derogation shall apply until the said date. ◄

31. (a) Creosote; wash oil CAS No 8001-58-9 EC No 232-287-5 (b) Creosote oil; wash oil CAS No 61789-28-4 EC No 263-047-8 (c) Distillates (coal tar), naphthalene oils; naphthalene oil CAS No 84650-04-4 EC No 283-484-8 (d) Creosote oil, acenaphthene fraction; wash oil CAS No 90640-84-9 EC No 283-484-8EC No 292-605-3 (e) Distillates (coal tar), upper; heavy anthracene oil CAS No 65996-91-0 EC No 266-026-1 (f) Anthracene oil CAS No 90640-80-5 EC No 292-602-7 (g) Tar acids, coal, crude; crude phenols CAS No 65996-85-2 EC No 266-019-3 (h) Creosote, wood CAS No 8021-39-4 EC No 232-419-1 (i) Low temperature tar oil, alkaline; extract residues (coal), low temperature coal tar alkaline CAS No 122384-78-5 EC No 310-191-5

1. Shall not be placed on the market, or used, as substances or in mixtures where the substance or mixture is intended for the treatment of wood. Furthermore, wood so treated shall not be placed on the market. 2. By way of derogation from paragraph 1: (a) The substances and mixtures may be used for wood treatment in industrial installations or by professionals covered by Community legislation on the protection of workers for in situ retreatment only if they contain: (i) benzo[a]pyrene at a concentration of less than 50 mg/kg (0,005 % by weight), and (ii) water extractable phenols at a concentration of less than 3 % by weight. Such substances and mixtures for use in wood treatment in industrial installations or by professionals: — may be placed on the market only in packaging of a capacity equal to or greater than 20 litres, — shall not be sold to consumers. Without prejudice to the application of other Community provisions on the classification, packaging and labelling of substances and mixtures, suppliers shall ensure before the placing on the market that the packaging of such substances and mixtures is visibly, legibly and indelibly marked as follows: ‘For use in industrial installations or professional treatment only’. (b) Wood treated in industrial installations or by professionals according to subparagraph (a) which is placed on the market for the first time or retreated in situ may be used for professional and industrial use only, for example on railways, in electric power transmission and telecommunications, for fencing, for agricultural purposes (for example stakes for tree support) and in harbours and waterways. (c) The prohibition in paragraph 1 on the placing on the market shall not apply to wood which has been treated with substances listed in entry 31 (a) to (i) before 31 December 2002 and is placed on the second-hand market for re-use. 3. Treated wood referred to under paragraph 2(b) and (c) shall not be used: — inside buildings, whatever their purpose, — in toys, — in playgrounds, — in parks, gardens, and outdoor recreational and leisure facilities where there is a risk of frequent skin contact, — in the manufacture of garden furniture such as picnic tables, — for the manufacture and use and any re-treatment of: — — containers intended for growing purposes, — packaging that may come into contact with raw materials, intermediate or finished products destined for human and/or animal consumption, — other materials which may contaminate the articles mentioned above.

32. Chloroform CAS No 67-66-3 EC No 200-663-8 34. 1,1,2-Trichloroethane CAS No 79-00-5 EC No 201-166-9 35. 1,1,2,2-Tetrachloroethane CAS No 79-34-5 EC No 201-197-8 36. 1,1,1,2-Tetrachloroethane CAS No 630-20-6 37. Pentachloroethane CAS No 76-01-7 EC No 200-925-1 38. 1,1-Dichloroethene CAS No 75-35-4 EC No 200-864-0

Without prejudice to the other parts of this Annex, the following shall apply to entries 32 to 38. 1. Shall not be placed on the market, or used, — as substances, — as constituents of other substances, or in mixtures in concentrations equal to or greater than 0,1 % by weight, where the substance or mixture is intended for supply to the general public and/or is intended for diffusive applications such as in surface cleaning and cleaning of fabrics. 2. Without prejudice to the application of other Community provisions on the classification, packaging and labelling of substances and mixtures, suppliers shall ensure before the placing on the market that the packaging of such substances and mixtures containing them in concentrations equal to or greater than 0,1 % by weight is visibly, legibly and indelibly marked as follows: ‘For use in industrial installations only’. By way of derogation this provision shall not apply to: (a) medicinal or veterinary products as defined by Directive 2001/82/EC and Directive 2001/83/EC; (b) cosmetic products as defined by Directive 76/768/EEC.

►M3 40. Substances classified as flammable gases category 1 or 2, flammable liquids categories 1, 2 or 3, flammable solids category 1 or 2, substances and mixtures which, in contact with water, emit flammable gases, category 1, 2 or 3, pyrophoric liquids category 1 or pyrophoric solids category 1, regardless of whether they appear in Part 3 of Annex VI to that Regulation or not. ◄

1. Shall not be used, as substance or as mixtures in aerosol dispensers where these aerosol dispensers are intended for supply to the general public for entertainment and decorative purposes such as the following: — metallic glitter intended mainly for decoration, — artificial snow and frost, — ‘whoopee’ cushions, — silly string aerosols, — imitation excrement, — horns for parties, — decorative flakes and foams, — artificial cobwebs, — stink bombs. 2. Without prejudice to the application of other Community provisions on the classification, packaging and labelling of substances, suppliers shall ensure before the placing on the market that the packaging of aerosol dispensers referred to above is marked visibly, legibly and indelibly with: ‘For professional users only’. 3. By way of derogation, paragraphs 1 and 2 shall not apply to the aerosol dispensers referred to Article 8 (1a) of Council Directive 75/324/EEC (²). 4. The aerosol dispensers referred to in paragraphs 1 and 2 shall not be placed on the market unless they conform to the requirements indicated.

41. Hexachloroethane CAS No 67-72-1 EC No 200-666-4

Shall not be placed on the market, or used, as substance or in mixtures, where the substance or mixture is intended for the manufacturing or processing of non-ferrous metals.

42. Alkanes, C₁₀-C₁₃, chloro (short-chain chlorinated paraffins) (SCCPs) EC No 287-476-5 CAS No 85535-84-8

Shall not be placed on the market, or used as substances, or as constituents of other substances or in mixtures in concentrations greater than 1 % by weight, where the substance or mixture is intended for: — metalworking, — fat liquoring of leather.

43. Azocolourants and Azodyes

1. Azodyes which, by reductive cleavage of one or more azo groups, may release one or more of the aromatic amines listed in Appendix 8, in detectable concentrations, i.e. above 30 mg/kg (0,003 % by weight) in the articles or in the dyed parts thereof, according to the testing methods listed in Appendix 10, shall not be used, in textile and leather articles which may come into direct and prolonged contact with the human skin or oral cavity, such as: — clothing, bedding, towels, hairpieces, wigs, hats, nappies and other sanitary items, sleeping bags, — footwear, gloves, wristwatch straps, handbags, purses/wallets, briefcases, chair covers, purses worn round the neck, — textile or leather toys and toys which include textile or leather garments, — yarn and fabrics intended for use by the final consumer. 2. Furthermore, the textile and leather articles referred to in paragraph 1 shall not be placed on the market unless they conform to the requirements set out in that paragraph. 3. Azodyes, which are contained in Appendix 9, ‘List of azodyes’ shall not be placed on the market, or used, as substances, or in mixtures in concentrations greater than 0,1 % by weight, where the substance or the mixture is intended for colouring textile and leather articles.

▼M9 —————

▼M5

45. Diphenylether, octabromo derivative C₁₂H₂Br₈O

1. Shall not be placed on the market, or used: — as a substance, — as a constituent of other substances, or in mixtures, in concentrations greater than 0,1 % by weight. 2. Articles shall not be placed on the market if they, or flame-retardant parts thereof, contain this substance in concentrations greater than 0,1 % by weight. 3. By way of derogation, paragraph 2 shall not apply: — to articles that were in use in the Community before 15 August 2004, — to electrical and electronic equipment within the scope of Directive 2002/95/EC.

46. (a) Nonylphenol C₆H4(OH)C₉H₁₉ CAS 25154-52-3 EC 246-672-0 (b) Nonylphenol ethoxylates (C₂H₄O)_nC₁₅H₂₄O

Shall not be placed on the market, or used, as substances or in mixtures in concentrations equal to or greater than 0,1 % by weight for the following purposes: (1) industrial and institutional cleaning except: — controlled closed dry cleaning systems where the washing liquid is recycled or incinerated, — cleaning systems with special treatment where the washing liquid is recycled or incinerated. (2) domestic cleaning; (3) textiles and leather processing except: — processing with no release into waste water, — systems with special treatment where the process water is pre-treated to remove the organic fraction completely prior to biological waste water treatment (degreasing of sheepskin); (4) emulsifier in agricultural teat dips; (5) metal working except: uses in controlled closed systems where the washing liquid is recycled or incinerated; (6) manufacturing of pulp and paper; (7) cosmetic products; (8) other personal care products except: spermicides; (9) co-formulants in pesticides and biocides. However national authorisations for pesticides or biocidal products containing nonylphenol ethoxylates as co-formulant, granted before 17 July 2003, shall not be affected by this restriction until their date of expiry.

47. Chromium VI compounds

1. Cement and cement-containing mixtures shall not be placed on the market, or used, if they contain, when hydrated, more than 2 mg/kg (0,0002 %) soluble chromium VI of the total dry weight of the cement. 2. If reducing agents are used, then without prejudice to the application of other Community provisions on the classification, packaging and labelling of substances and mixtures, suppliers shall ensure before the placing on the market that the packaging of cement or cement-containing mixtures is visibly, legibly and indelibly marked with information on the packing date, as well as on the storage conditions and the storage period appropriate to maintaining the activity of the reducing agent and to keeping the content of soluble chromium VI below the limit indicated in paragraph 1. 3. By way of derogation, paragraphs 1 and 2 shall not apply to the placing on the market for, and use in, controlled closed and totally automated processes in which cement and cement-containing mixtures are handled solely by machines and in which there is no possibility of contact with the skin.

48. Toluene CAS No 108-88-3 EC No 203-625-9

Shall not be placed on the market, or used, as a substance or in mixtures in a concentration equal to or greater than 0,1 % by weight where the substance or mixture is used in adhesives or spray paints intended for supply to the general public.

49. Trichlorobenzene CAS No 120-82-1 EC No 204-428-0

Shall not be placed on the market, or used, as a substance or in mixtures in a concentration equal to or greater than 0,1 % by weight for any use except: — as an intermediate of synthesis, or, — as a process solvent in closed chemical applications for chlorination reactions, or, — in the manufacture of 1,3,5-triamino — 2,4,6-trinitrobenzene (TATB).

50. Polycyclic-aromatic hydrocarbons (PAH) (a) Benzo[a]pyrene (BaP) CAS No 50-32-8 (b) Benzo[e]pyrene (BeP) CAS No 192-97-2 (c) Benzo[a]anthracene (BaA) CAS No 56-55-3 (d) Chrysen (CHR) CAS No 218-01-9 (e) Benzo[b]fluoranthene (BbFA) CAS No 205-99-2 (f) Benzo[j]fluoranthene (BjFA) CAS No 205-82-3 (g) Benzo[k]fluoranthene (BkFA) CAS No 207-08-9 (h) Dibenzo[a,h]anthracene (DBAhA) CAS No 53-70-3

1. From 1 January 2010, extender oils shall not be placed on the market, or used for the production of tyres or parts of tyres if they contain: — more than 1 mg/kg (0,0001 % by weight) BaP, or, — more than 10 mg/kg (0,001 % by weight) of the sum of all listed PAHs. These limits shall be regarded as kept, if the polycyclic aromatics (PCA) extract is less than 3 % by weight as measured by the Institute of Petroleum standard IP346: 1998 (Determination of PCA in unused lubricating base oils and asphaltene free petroleum fractions — Dimethyl sulphoxide extraction refractive index method), provided that compliance with the limit values of BaP and of the listed PAHs, as well as the correlation of the measured values with the PCA extract, is controlled by the manufacturer or importer every six months or after each major operational change, whichever is earlier. 2. Furthermore, tyres and treads for retreading manufactured after 1 January 2010 shall not be placed on the market if they contain extender oils exceeding the limits indicated in paragraph 1. These limits shall be regarded as kept, if the vulcanised rubber compounds do not exceed the limit of 0,35 % Bay protons as measured and calculated by ISO 21461 (Rubber vulcanised — Determination of aromaticity of oil in vulcanised rubber compounds). 3. By way of derogation, paragraph 2 shall not apply to retreaded tyres if their tread does not contain extender oils exceeding the limits referred to in paragraph 1. 4. For the purpose of this entry ‘tyres’ shall mean tyres for vehicles covered by: — Directive 2007/46/EC of the European Parliament and of the Council of 5 September 2007 establishing a framework for the approval of motor vehicles and their trailers (⁴), — Directive 2003/37/EC of the European Parliament and of the Council of 26 May 2003 on type-approval of agricultural or forestry tractors, their trailers and interchangeable towed machinery, together with their systems, components and separate technical units (⁵), and — Directive 2002/24/EC of the European Parliament and of the Council of 18 March 2002 relating to the type-approval of two or three-wheel motor vehicles and repealing Council Directive 92/61/EEC (⁶).

51. The following phthalates (or other CAS and EC numbers covering the substance): (a) Bis (2-ethylhexyl) phthalate (DEHP) CAS No 117-81-7 EC No 204-211-0 (b) Dibutyl phthalate (DBP) CAS No 84-74-2 EC No 201-557-4 (c) Benzyl butyl phthalate (BBP) CAS No 85-68-7 EC No 201-622-7

1. Shall not be used as substances or in mixtures, in concentrations greater than 0,1 % by weight of the plasticised material, in toys and childcare articles. 2. Toys and childcare articles containing these phthalates in a concentration greater than 0,1 % by weight of the plasticised material shall not be placed on the market. 3. The Commission shall re-evaluate, by 16 January 2010, the measures provided for in relation to this entry in the light of new scientific information on such substances and their substitutes, and if justified, these measures shall be modified accordingly. 4. For the purpose of this entry ‘childcare article’ shall mean any product intended to facilitate sleep, relaxation, hygiene, the feeding of children or sucking on the part of children.

52. The following phthalates (or other CAS- and EC numbers covering the substance): (a) Di-‘isononyl’ phthalate (DINP) CAS No 28553-12-0 and 68515-48-0 EC No 249-079-5 and 271-090-9 (b) Di-‘isodecyl’ phthalate (DIDP) CAS No 26761-40-0 and 68515-49-1 EC No 247-977-1 and 271-091-4 (c) Di-n-octyl phthalate (DNOP) CAS No 117-84-0 EC No 204-214-7

1. Shall not be used as substances or in mixtures, in concentrations greater than 0,1 % by weight of the plasticised material, in toys and childcare articles which can be placed in the mouth by children. 2. Such toys and childcare articles containing these phthalates in a concentration greater than 0,1 % by weight of the plasticised material shall not be placed on the market. 3. The Commission shall re-evaluate, by 16 January 2010, the measures provided for in relation to this entry in the light of new scientific information on such substances and their substitutes, and if justified, these measures shall be modified accordingly. 4. For the purpose of this entry ‘childcare article’ shall mean any product intended to facilitate sleep, relaxation, hygiene, the feeding of children or sucking on the part of children.

▼M9 —————

▼M5

54. 2-(2-methoxyethoxy)ethanol (DEGME) CAS No 111-77-3 EC No 203-906-6

Shall not be placed on the market after 27 June 2010, for supply to the general public, as a constituent of paints, paint strippers, cleaning agents, self-shining emulsions or floor sealants in concentrations equal to or greater than 0,1 % by weight.

55. 2-(2-butoxyethoxy)ethanol (DEGBE) CAS No 112-34-5 EC No 203-961-6

1. Shall not be placed on the market for the first time after 27 June 2010, for supply to the general public, as a constituent of spray paints or spray cleaners in aerosol dispensers in concentrations equal to or greater than 3 % by weight. 2. Spray paints and spray cleaners in aerosol dispensers containing DEGBE and not conforming to paragraph 1 shall not be placed on the market for supply to the general public after 27 December 2010. 3. Without prejudice to other Community legislation concerning the classification, packaging and labelling of substances and mixtures, suppliers shall ensure before the placing on the market that paints other than spray paints containing DEGBE in concentrations equal to or greater than 3 % by weight of that are placed on the market for supply to the general public are visibly, legibly and indelibly marked by 27 December 2010 as follows: ‘Do not use in paint spraying equipment’.

56. Methylenediphenyl diisocyanate (MDI) CAS No 26447-40-5 EC No 247-714-0

1. Shall not be placed on the market after 27 December 2010, as a constituent of mixtures in concentrations equal to or greater than 0,1 % by weight of MDI for supply to the general public, unless suppliers shall ensure before the placing on the market that the packaging: (a) contains protective gloves which comply with the requirements of Council Directive 89/686/EEC (⁹); (b) is marked visibly, legibly and indelibly as follows, and without prejudice to other Community legislation concerning the classification, packaging and labelling of substances and mixtures: ‘— Persons already sensitised to diisocyanates may develop allergic reactions when using this product. — Persons suffering from asthma, eczema or skin problems should avoid contact, including dermal contact, with this product. — This product should not be used under conditions of poor ventilation unless a protective mask with an appropriate gas filter (i.e. type A1 according to standard EN 14387) is used.’ 2. By way of derogation, paragraph 1(a) shall not apply to hot melt adhesives.

57. Cyclohexane CAS No 110-82-7 EC No 203-806-2

1. Shall not be placed on the market for the first time after 27 June 2010, for supply to the general public, as a constituent of neoprene-based contact adhesives in concentrations equal to or greater than 0,1 % by weight in package sizes greater than 350 g. 2. Neoprene-based contact adhesives containing cyclohexane and not conforming to paragraph 1 shall not be placed on the market for supply to the general public after 27 December 2010. 3. Without prejudice to other Community legislation concerning the classification, packaging and labelling of substances and mixtures, suppliers shall ensure before the placing on the market that neoprene-based contact adhesives containing cyclohexane in concentrations equal to or greater than 0,1 % by weight that are placed on the market for supply to the general public after 27 December 2010 are visibly, legibly and indelibly marked as follows: ‘— This product is not to be used under conditions of poor ventilation. — This product is not to be used for carpet laying.’.

58. Ammonium nitrate (AN) CAS No 6484-52-2 EC No 229-347-8

1. Shall not be placed on the market for the first time after 27 June 2010 as a substance, or in mixtures that contain more than 28 % by weight of nitrogen in relation to ammonium nitrate, for use as a solid fertiliser, straight or compound, unless the fertiliser complies with the technical provisions for ammonium nitrate fertilisers of high nitrogen content set out in Annex III to Regulation (EC) No 2003/2003 of the European Parliament and of the Council (¹⁰). 2. Shall not be placed on the market after 27 June 2010 as a substance, or in mixtures that contain 16 % or more by weight of nitrogen in relation to ammonium nitrate except for supply to: (a) downstream users and distributors, including natural or legal persons licensed or authorised in accordance with Council Directive 93/15/EEC (¹¹); (b) farmers for use in agricultural activities, either full time or part time and not necessarily related to the size of the land area. For the purposes of this subparagraph: (i) ‘farmer’ shall mean a natural or legal person, or a group of natural or legal persons, whatever legal status is granted to the group and its members by national law, whose holding is situated within Community territory, as referred to in Article 299 of the Treaty, and who exercises an agricultural activity; (ii) ‘agricultural activity’ shall mean the production, rearing or growing of agricultural products including harvesting, milking, breeding animals and keeping animals for farming purposes, or maintaining the land in good agricultural and environmental condition as established under Article 5 of Council Regulation (EC) No 1782/2003 (¹²); (c) natural or legal persons engaged in professional activities such as horticulture, plant growing in greenhouses, maintenance of parks, gardens or sport pitches, forestry or other similar activities. 3. However, for the restrictions in paragraph 2, Member States may until 1 July 2014, for socioeconomic reasons, apply a limit of up to 20 % by weight of nitrogen in relation to ammonium nitrate for substances and mixtures placed on the market within their territories. They shall inform the Commission and other Member States thereof.

▼M6

59. Dichloromethane CAS No 75-09-2 EC No: 200-838-9

1. Paint strippers containing dichloromethane in a concentration equal to or greater than 0,1 % by weight shall not be: (a) placed on the market for the first time for supply to the general public or to professionals after 6 December 2010; (b) placed on the market for supply to the general public or to professionals after 6 December 2011; (c) used by professionals after 6 June 2012. For the purposes of this entry: (i) ‘professional’ means any natural or legal person, including workers and self-employed workers undertaking paint stripping in the course of their professional activity outside an industrial installation; (ii) ‘industrial installation’ means a facility used for paint stripping activities. 2. By way of derogation from paragraph 1, Member States may allow on their territories and for certain activities the use, by specifically trained professionals, of paint strippers containing dichloromethane and may allow the placing on the market of such paint strippers for supply to those professionals. Member States making use of this derogation shall define appropriate provisions for the protection of the health and safety of those professionals using paint strippers containing dichloromethane and shall inform the Commission thereof. Those provisions shall include a requirement that a professional shall hold a certificate that is accepted by the Member State in which that professional operates, or provide other documentary evidence to that effect, or be otherwise approved by that Member State, so as to demonstrate proper training and competence to safely use paint strippers containing dichloromethane. The Commission shall prepare a list of the Member States which have made use of the derogation in this paragraph and make it publicly available over the Internet. 3. A professional benefiting from the derogation referred to in paragraph 2 shall operate only in Member States which have made use of that derogation. The training referred to in paragraph 2 shall cover as a minimum: (a) awareness, evaluation and management of risks to health, including information on existing substitutes or processes, which under their conditions of use are less hazardous to the health and safety of workers; (b) use of adequate ventilation; (c) use of appropriate personal protective equipment that complies with Directive 89/686/EEC. Employers and self-employed workers shall preferably replace dichloromethane with a chemical agent or process which, under its conditions of use, presents no risk, or a lower risk, to the health and safety of workers. Professional shall apply all relevant safety measures in practice, including the use of personal protective equipment. 4. Without prejudice to other Community legislation on workers protection, paint strippers containing dichloromethane in concentrations equal to or greater than 0,1 % by weight may be used in industrial installations only if the following minimum conditions are met: (a) effective ventilation in all processing areas, in particular for the wet processing and the drying of stripped articles: local exhaust ventilation at strip tanks supplemented by forced ventilation in those areas, so as to minimise exposure and to ensure compliance, where technically feasible, with relevant occupational exposure limits; (b) measures to minimise evaporation from strip tanks comprising: lids for covering strip tanks except during loading and unloading; suitable loading and unloading arrangements for strip tanks; and wash tanks with water or brine to remove excess solvent after unloading; (c) measures for the safe handling of dichloromethane in strip tanks comprising: pumps and pipework for transferring paint stripper to and from strip tanks; and suitable arrangements for safe cleaning of tanks and removal of sludge; (d) personal protective equipment that complies with Directive 89/686/EEC comprising: suitable protective gloves, safety goggles and protective clothing; and appropriate respiratory protective equipment where compliance with relevant occupational exposure limits cannot be otherwise achieved; (e) adequate information, instruction and training for operators in the use of such equipment. 5. Without prejudice to other Community provisions concerning the classification, labelling and packaging of substances and mixtures, by 6 December 2011 paint strippers containing dichloromethane in a concentration equal to or greater than 0,1 % by weight shall be visibly, legibly and indelibly marked as follows: ‘Restricted to industrial use and to professionals approved in certain EU Member States — verify where use is allowed.’

▼M12

60. Acrylamide CAS No 79-06-1

Shall not be placed on the market or used as a substance or constituent of mixtures in a concentration, equal to or greater than 0,1 % by weight for grouting applications after 5 November 2012.

▼M16

61. Dimethylfumarate (DMF) CAS No 624-49-7 EC 210-849-0

Shall not be used in articles or any parts thereof in concentrations greater than 0,1 mg/kg. Articles or any parts thereof containing DMF in concentrations greater than 0,1 mg/kg shall not be placed on the market.

(¹) OJ L 256, 7.9.1987, p. 42. (²) OJ L 147, 9.6.1975, p. 40. (³) OJ L 37, 13.2.2003, p. 19. (⁴) OJ L 263, 9.10.2007, p. 1. (⁵) OJ L 171, 9.7.2003, p. 1. (⁶) OJ L 124, 9.5.2002, p. 1. (⁷) OJ L 24, 29.1.2008, p. 8. (⁸) OJ L 104, 8.4.2004, p. 1. (⁹) OJ L 399, 30.12.1989, p. 18. (¹⁰) OJ L 304, 21.11.2003, p. 1. (¹¹) OJ L 121, 15.5.1993, p. 20. (¹²) OJ L 270, 21.10.2003, p. 1. (¹³) OJ L 365, 31.12.1994, p. 10.

Substances

Index No

EC No

CAS No

Notes

Chromium (VI) trioxide

024-001-00-0

215-607-8

1333-82-0

►M5 E ◄

Zinc chromates including zinc potassium chromate

024-007-00-3

▼M14

Nickel monoxide; [1]

028-003-00-2

215-215-7 [1]

1313-99-1 [1]

Nickel oxide; [2]

234-323-5 [2]

11099-02-8 [2]

Bunsenite; [3]

- [3]

34492-97-2 [3]

Nickel dioxide

028-004-00-8

234-823-3

12035-36-8

Dinickel trioxide

028-005-00-3

215-217-8

1314-06-3

Nickel (II) sulfide; [1]

028-006-00-9

240-841-2 [1]

16812-54-7 [1]

Nickel sulfide; [2]

234-349-7 [2]

11113-75-0 [2]

Millerite; [3]

- [3]

1314-04-1 [3]

Trinickel disulfide;

028-007-00-4

Nickel subsulfide; [1]

234-829-6 [1]

12035-72-2 [1]

Heazlewoodite; [2]

- [2]

12035-71-1 [2]

▼M14

Nickel dihydroxide; [1]

028-008-00-X

235-008-5 [1]

12054-48-7 [1]

Nickel hydroxide; [2]

234-348-1 [2]

11113-74-9 [2]

Nickel sulfate

028-009-00-5

232-104-9

7786-81-4

Nickel carbonate;

028-010-00-0

Basic nickel carbonate;

Carbonic acid, nickel (2+) salt; [1]

222-068-2 [1]

3333-67-3 [1]

Carbonic acid, nickel salt; [2]

240-408-8 [2]

16337-84-1 [2]

[μ-[carbonato(2-)-O:O′]] dihydroxy trinickel; [3]

265-748-4 [3]

65405-96-1 [3]

[carbonato(2-)] tetrahydroxytrinickel; [4]

235-715-9 [4]

12607-70-4 [4]

Nickel dichloride

028-011-00-6

231-743-0

7718-54-9

Nickel dinitrate; [1]

028-012-00-1

236-068-5 [1]

13138-45-9 [1]

Nitric acid, nickel salt; [2]

238-076-4 [2]

14216-75-2 [2]

Nickel matte

028-013-00-7

273-749-6

69012-50-6

Slimes and sludges, copper electrolytic refining, decopperised, nickel sulphate

028-014-00-2

295-859-3

92129-57-2

Slimes and sludges, copper electrolyte refining, decopperised

028-015-00-8

305-433-1

94551-87-8

Nickel diperchlorate; Perchloric acid, nickel (II) salt

028-016-00-3

237-124-1

13637-71-3

Nickel dipotassium bis(sulfate); [1]

028-017-00-9

237-563-9 [1]

13842-46-1 [1]

Diammonium nickel bis(sulfate); [2]

239-793-2 [2]

15699-18-0 [2]

Nickel bis(sulfamidate); Nickel sulfamate

028-018-00-4

237-396-1

13770-89-3

Nickel bis(tetrafluoroborate)

028-019-00-X

238-753-4

14708-14-6

Nickel diformate; [1]

028-021-00-0

222-101-0 [1]

3349-06-2 [1]

Formic acid, nickel salt; [2]

239-946-6 [2]

15843-02-4 [2]

Formic acid, copper nickel salt; [3]

268-755-0 [3]

68134-59-8 [3]

Nickel di(acetate); [1]

028-022-00-6

206-761-7 [1]

373-02-4 [1]

Nickel acetate; [2]

239-086-1 [2]

14998-37-9 [2]

Nickel dibenzoate

028-024-00-7

209-046-8

553-71-9

Nickel bis(4-cyclohexylbutyrate)

028-025-00-2

223-463-2

3906-55-6

Nickel (II) stearate; Nickel (II) octadecanoate

028-026-00-8

218-744-1

2223-95-2

Nickel dilactate

028-027-00-3

—

16039-61-5

Nickel (II) octanoate

028-028-00-9

225-656-7

4995-91-9

Nickel difluoride; [1]

028-029-00-4

233-071-3 [1]

10028-18-9 [1]

Nickel dibromide; [2]

236-665-0 [2]

13462-88-9 [2]

Nickel diiodide; [3]

236-666-6 [3]

13462-90-3 [3]

Nickel potassium fluoride; [4]

- [4]

11132-10-8 [4]

Nickel hexafluorosilicate

028-030-00-X

247-430-7

26043-11-8

Nickel selenate

028-031-00-5

239-125-2

15060-62-5

Nickel hydrogen phosphate; [1]

028-032-00-0

238-278-2 [1]

14332-34-4 [1]

Nickel bis(dihydrogen phosphate); [2]

242-522-3 [2]

18718-11-1 [2]

Trinickel bis(orthophosphate); [3]

233-844-5 [3]

10381-36-9 [3]

Dinickel diphosphate; [4]

238-426-6 [4]

14448-18-1 [4]

Nickel bis(phosphinate); [5]

238-511-8 [5]

14507-36-9 [5]

Nickel phosphinate; [6]

252-840-4 [6]

36026-88-7 [6]

Phosphoric acid, calcium nickel salt; [7]

- [7]

17169-61-8 [7]

Diphosphoric acid, nickel (II) salt; [8]

- [8]

19372-20-4 [8]

Diammonium nickel hexacyanoferrate

028-033-00-6

—

74195-78-1

Nickel dicyanide

028-034-00-1

209-160-8

557-19-7

Nickel chromate

028-035-00-7

238-766-5

14721-18-7

Nickel (II) silicate; [1]

028-036-00-2

244-578-4 [1]

21784-78-1 [1]

Dinickel orthosilicate; [2]

237-411-1 [2]

13775-54-7 [2]

Nickel silicate (3:4); [3]

250-788-7 [3]

31748-25-1 [3]

Silicic acid, nickel salt; [4]

253-461-7 [4]

37321-15-6 [4]

Trihydrogen hydroxybis[orthosilicato(4-)]trinickelate(3-); [5]

235-688-3 [5]

12519-85-6 [5]

Dinickel hexacyanoferrate

028-037-00-8

238-946-3

14874-78-3

Trinickel bis(arsenate); Nickel (II) arsenate

028-038-00-3

236-771-7

13477-70-8

Nickel oxalate; [1]

028-039-00-9

208-933-7 [1]

547-67-1 [1]

Oxalic acid, nickel salt; [2]

243-867-2 [2]

20543-06-0 [2]

Nickel telluride

028-040-00-4

235-260-6

12142-88-0

Trinickel tetrasulfide

028-041-00-X

—

12137-12-1

Trinickel bis(arsenite)

028-042-00-5

—

74646-29-0

Cobalt nickel gray periclase;

028-043-00-0

C.I. Pigment Black 25;

C.I. 77332; [1]

269-051-6 [1]

68186-89-0 [1]

Cobalt nickel dioxide; [2]

261-346-8 [2]

58591-45-0 [2]

Cobalt nickel oxide; [3]

- [3]

12737-30-3 [3]

Nickel tin trioxide; Nickel stannate

028-044-00-6

234-824-9

12035-38-0

Nickel triuranium decaoxide

028-045-00-1

239-876-6

15780-33-3

Nickel dithiocyanate

028-046-00-7

237-205-1

13689-92-4

Nickel dichromate

028-047-00-2

239-646-5

15586-38-6

Nickel (II) selenite

028-048-00-8

233-263-7

10101-96-9

Nickel selenide

028-049-00-3

215-216-2

1314-05-2

Silicic acid, lead nickel salt

028-050-00-9

—

68130-19-8

Nickel diarsenide; [1]

028-051-00-4

235-103-1 [1]

12068-61-0 [1]

Nickel arsenide; [2]

248-169-1 [2]

27016-75-7 [2]

Nickel barium titanium primrose priderite;

028-052-00-X

271-853-6

68610-24-2

C.I. Pigment Yellow 157;

C.I. 77900

Nickel dichlorate; [1]

028-053-00-5

267-897-0 [1]

67952-43-6 [1]

Nickel dibromate; [2]

238-596-1 [2]

14550-87-9 [2]

Ethyl hydrogen sulfate, nickel (II) salt; [3]

275-897-7 [3]

71720-48-4 [3]

Nickel (II) trifluoroacetate; [1]

028-054-00-0

240-235-8 [1]

16083-14-0 [1]

Nickel (II) propionate; [2]

222-102-6 [2]

3349-08-4 [2]

Nickel bis(benzenesulfonate); [3]

254-642-3 [3]

39819-65-3 [3]

Nickel (II) hydrogen citrate; [4]

242-533-3 [4]

18721-51-2 [4]

Citric acid, ammonium nickel salt; [5]

242-161-1 [5]

18283-82-4 [5]

Substances

Index No

EC No

CAS No

Notes

Beryllium

004-001-00-7

231-150-7

7440-41-7

Beryllium compounds with the exception of aluminium beryllium silicates

004-002-00-2

Beryllium oxide

004-003-00-8

215-133-1

1304-56-9

►M5 E ◄

Sulfallate (ISO); 2-chlorallyl diethyldithiocarbamate

006-038-00-4

202-388-9

95-06-7

Dimethylcarbamoyl chloride

006-041-00-0

201-208-6

79-44-7

Diazomethane

006-068-00-8

206-382-7

334-88-3

▼M14

O-isobutyl-N-ethoxy carbonylthiocarbamate

006-094-00-X

434-350-4

103122-66-3

O-hexyl-N-ethoxycarbonylthiocarbamate

006-102-00-1

432-750-3

—

▼C1

Hydrazine

007-008-00-3

206-114-9

302-01-2

►M5 E ◄

N,N-Dimethylhydrazine

007-012-00-5

200-316-0

57-14-7

1,2-Dimethylhydrazine

007-013-00-0

540-73-8

►M5 E ◄

Salts of hydrazine

007-014-00-6

Isobutyl nitrite

007-017-00-2

208-819-7

542-56-3

►M5 E ◄

Hydrazobenzene; 1,2-diphenylhydrazine

007-021-00-4

204-563-5

122-66-7

Hydrazine bis(3-carboxy-4-hydroxybenzensulfonate)

007-022-00-X

405-030-1

Hexamethylphosphoric triamide; hexamethylphosphoramide

015-106-00-2

211-653-8

680-31-9

▼M14

Mixture of: dimethyl(2-(hydroxymethylcarbamoyl)ethyl)phosphonate; Diethyl(2-(hydroxymethylcarbamoyl)ethyl)phosphonate; Methyl ethyl(2-(hydroxymethylcarbamoyl)ethyl)phosphonate

015-196-00-3

435-960-3

—

▼C1

Dimethyl sulphate

016-023-00-4

201-058-1

77-78-1

►M5 E ◄

Diethyl sulphate

016-027-00-6

200-589-6

64-67-5

1,3-Propanesultone

016-032-00-3

214-317-9

1120-71-4

Dimethylsulfamoylchloride

016-033-00-9

236-412-4

13360-57-1

Potassium dichromate

024-002-00-6

231-906-6

7778-50-9

►M5 E ◄

Ammonium dichromate

024-003-00-1

232-143-1

7789-09-5

►M5 E ◄

▼M14

Sodium dichromate

024-004-00-7

234-190-3

10588-01-9

▼M14 —————

▼C1

Chromyl dichloride; chromic oxychloride

024-005-00-2

239-056-8

14977-61-8

Potassium chromate

024-006-00-8

232-140-5

7789-00-6

Calcium chromate

024-008-00-9

237-366-8

13765-19-0

Strontium chromate

024-009-00-4

232-142-6

7789-06-2

Chromium III chromate; chromic chromate

024-010-00-X

246-356-2

24613-89-6

Chromium (VI) compounds, with the exception of barium chromate and of compounds specified elsewhere in ►M5 Annex VI to Regulation (EC) No 1272/2008 ◄

024-017-00-8

—

—

Sodium chromate

024-018-00-3

231-889-5

7775-11-3

►M5 E ◄

Cobalt dichloride

027-004-00-5

231-589-4

7646-79-9

►M5 E ◄

Cobalt sulphate

027-005-00-0

233-334-2

10124-43-3

►M5 E ◄

▼M14

Cobalt acetate

027-006-00-6

200-755-8

71-48-7

Cobalt nitrate

027-009-00-2

233-402-1

10141-05-6

Cobalt carbonate

027-010-00-8

208-169-4

513-79-1

▼C1

Potassium bromate

035-003-00-6

231-829-8

7758-01-2

Cadmium oxide

048-002-00-0

215-146-2

1306-19-0

►M5 E ◄

Cadmium fluoride

048-006-00-2

232-222-0

7790-79-6

►M5 E ◄

Cadmium chloride

048-008-00-3

233-296-7

10108-64-2

►M5 E ◄

Cadmium sulphate

048-009-00-9

233-331-6

10124-36-4

►M5 E ◄

Cadmium sulphide

048-010-00-4

215-147-8

1306-23-6

►M5 E ◄

Cadmium (pyrophoric)

048-011-00-X

231-152-8

7440-43-9

►M5 E ◄

▼M14

Lead chromate

082-004-00-2

231-846-0

7758-97-6

Lead sulfochromate yellow; C.I. Pigment Yellow 34; [This substance is identified in the Colour Index by Colour Index Constitution Number, C.I. 77603.]

082-009-00-X

215-693-7

1344-37-2

Lead chromate molybdate sulfate red; C.I. Pigment Red 104; [This substance is identified in the Colour Index by Colour Index Constitution Number, C.I. 77605.]

082-010-00-5

235-759-9

12656-85-8

▼C1

Isoprene (stabilised) 2-Methyl-1,3-butadiene

601-014-00-5

201-143-3

78-79-5

D

Benzo[a]pyrene; benzo[d,e,f]chrysene

601-032-00-3

200-028-5

50-32-8

Benzo[a]anthracene

601-033-00-9

200-280-6

56-55-3

Benzo[b]fluoranthene; benzo[e]acephenanthrylene

601-034-00-4

205-911-9

205-99-2

Benzo[j]fluoranthene

601-035-00-X

205-910-3

205-82-3

Benzo[k]fluoranthene

601-036-00-5

205-916-6

207-08-9

Dibenz[a, h]anthracene

601-041-00-2

200-181-8

53-70-3

Chrysene

601-048-00-0

205-923-4

218-01-9

Benzo[e]pyrene

601-049-00-6

205-892-7

192-97-2

1,2-Dibromoethane; ethylene dibromide

602-010-00-6

203-444-5

106-93-4

►M5 E ◄

1,2-Dichloroethane; ethylene dichloride

602-012-00-7

203-458-1

107-06-2

1,2-Dibromo-3-chloropropane

602-021-00-6

202-479-3

96-12-8

Bromoethylene

602-024-00-2

209-800-6

593-60-2

Trichloroethylene; trichloroethene

602-027-00-9

201-167-4

79-01-6

Chloroprene (stabilised) 2-Chlorobuta-1,3-diene

602-036-00-8

204-818-0

126-99-8

D ►M5, E ◄

α-Chlorotoluene; benzyl chloride

602-037-00-3

202-853-6

100-44-7

►M5 E ◄

α,α,α-Trichlorotoluene; benzotrichloride

602-038-00-9

202-634-5

98-07-7

1,2,3-Trichloropropane

602-062-00-X

202-486-1

96-18-4

D

1,3-Dichloro-2-propanol

602-064-00-0

202-491-9

96-23-1

Hexachlorobenzene

602-065-00-6

204-273-9

118-74-1

1,4-Dichlorobut-2-ene

602-073-00-X

212-121-8

764-41-0

►M5 E ◄

2,3-dibromopropan-1-ol; 2,3-dibromo-1-propanol

602-088-00-1

202-480-9

96-13-9

►M5 E ◄

α,α,α,4-Tetrachlorotoluene p-Chlorobenzotrichloride

602-093-00-9

226-009-1

5216-25-1

►M5 E ◄

Ethylene oxide; oxirane

603-023-00-X

200-849-9

75-21-8

1-Chloro-2,3-epoxypropane; epichlorhydrin

603-026-00-6

203-439-8

106-89-8

Propylene oxide; 1,2-epoxypropane; methyloxirane

603-055-00-4

200-879-2

75-56-9

►M5 E ◄

2,2'-Bioxirane; 1,2:3,4-diepoxybutane

603-060-00-1

215-979-1

1464-53-5

2,3-Epoxypropan-1-ol; glycidol oxiranemethanol

603-063-00-8

209-128-3

556-52-5

►M5 E ◄

Phenyl glycidyl ether; 2,3-epoxypropyl phenyl ether; 1,2-epoxy-3-phenoxypropane

603-067-00-X

204-557-2

122-60-1

►M5 E ◄

Styrene oxide; (epoxyethyl)benzene; phenyloxirane

603-084-00-2

202-476-7

96-09-3

Furan

603-105-00-5

203-727-3

110-00-9

►M5 E ◄

R-2,3-epoxy-1-propanol

603-143-00-2

404-660-4

57044-25-4

►M5 E ◄

(R)-1-chloro-2,3-epoxypropane

603-166-00-8

424-280-2

51594-55-9

▼M14

2,3-Epoxypropyltrimethylammonium chloride ...%; Glycidyl trimethylammonium chloride ...%

603-211-00-1

221-221-0

3033-77-0

B

1-(2-amino-5-chlorophenyl)-2,2,2-trifluoro-1,1-ethanediol, hydrochloride; [containing < 0,1 % 4-chloroaniline (EC No 203-401-0)]

603-221-01-3

433-580-2

214353-17-0

▼C1

4-Amino-3-fluorophenol

604-028-00-X

402-230-0

399-95-1

▼M14

Phenolphthalein

604-076-00-1

201-004-7

77-09-8

▼C1

5-Allyl-1,3-benzodioxole; safrole

605-020-00-9

202-345-4

94-59-7

►M5 E ◄

Substances

Index No

EC No

CAS No

Notes

▼M14

O-isobutyl-N-ethoxy carbonylthiocarbamate

006-094-00-X

434-350-4

103122-66-3

O-hexyl-N-ethoxycarbonylthiocarbamate

006-102-00-1

432-750-3

—

▼C1

Hexamethylphosphoric triamide; hexamethylphosphoramide

015-106-00-2

211-653-8

680-31-9

▼M14

Mixture of: dimethyl(2-(hydroxymethylcarbamoyl)ethyl)phosphonate; Diethyl(2-(hydroxymethylcarbamoyl)ethyl)phosphonate; Methyl ethyl(2-(hydroxymethylcarbamoyl)ethyl)phosphonate

015-196-00-3

435-960-3

—

▼C1

Diethyl sulphate

016-027-00-6

200-589-6

64-67-5

Chromium (VI) trioxide

024-001-00-0

215-607-8

1333-82-0

E

Potassium dichromate

024-002-00-6

231-906-6

7778-50-9

E

Ammonium dichromate

024-003-00-1

232-143-1

7789-09-5

E

▼M14

Sodium dichromate

024-004-00-7

234-190-3

10588-01-9

▼M14 —————

▼C1

Chromyl dichloride; chromic oxychloride

024-005-00-2

239-056-8

14977-61-8

Potassium chromate

024-006-00-8

232-140-5

7789-00-6

Sodium chromate

024-018-00-3

231-889-5

7775-11-3

E

Cadmium fluoride

048-006-00-2

232-222-0

7790-79-6

E

Cadmium chloride

048-008-00-3

233-296-7

10108-64-2

E

Cadmium sulphate

048-009-00-9

233-331-6

10124-36-4

E

Butane [containing ≥ 0,1 % Butadiene (203-450-8)] [1]

601-004-01-8

203-448-7 [1]

106-97-8 [1]

C, S

Isobutane [containing ≥ 0,1 % Butadiene (203-450-8)] [2]

20-857-2 [2]

75-28-5 [2]

1,3-Butadiene buta-1,3-diene

601-013-00-X

203-450-8

106-99-0

D

Benzene

601-020-00-8

200-753-7

71-43-2

E

Benzo[a]pyrene; benzo[d,e,f]chrysene

601-032-00-3

200-028-5

50-32-8

1,2-Dibromo-3-chloropropane

602-021-00-6

202-479-3

96-12-8

Ethylene oxide; oxirane

603-023-00-X

200-849-9

75-21-8

Propylene oxide; 1,2-epoxypropane; Methyloxirane

603-055-00-4

200-879-2

75-56-9

E

2,2'-Bioxirane; 1,2:3,4-diepoxybutane

603-060-00-1

215-979-1

1464-53-5

▼M14

2-Chloro-6-fluoro-phenol

604-082-00-4

433-890-8

2040-90-6

▼C1

Methyl acrylamidomethoxyacetate (containing ≥ 0,1 % acrylamide)

607-190-00-X

401-890-7

77402-03-0

Methyl acrylamidoglycolate (containing ≥ 0,1 % acrylamide)

607-210-00-7

403-230-3

77402-05-2

2-Nitrotoluene

609-065-00-5

201-853-3

88-72-2

E

4,4'-oxydianiline [1] and its salts p-aminophenyl ether [1]

612-199-00-7

202-977-0 [1]

101-80-4 [1]

E

▼M14

(2-chloroethyl)(3-hydroxypropyl)ammonium chloride

612-246-00-1

429-740-6

40722-80-3

▼C1

Ethyleneimine; aziridine

613-001-00-1

205-793-9

151-56-4

Carbendazim (ISO) methyl benzimidazol-2-ylcarbamate

613-048-00-8

234-232-0

10605-21-7

Benomyl (ISO) methyl 1-(butylcarbamoyl)benzimidazol-2-ylcarbamate

613-049-00-3

241-775-7

17804-35-2

▼M14

Colchicine

614-005-00-6

200-598-5

64-86-8

▼C1

1,3,5,-Tris(oxiranylmethyl)-1,3,5-triazine-2,4,6(1H,3H,5H)-trione; TGIC

615-021-00-6

219-514-3

2451-62-9

Acrylamide

616-003-00-0

201-173-7

79-06-1

1,3,5-tris-[(2S and 2R)-2,3-epoxypropyl]-1,3,5-triazine-2,4,6-(1H,3H,5H)-trione

616-091-00-0

423-400-0

59653-74-6

E

▼M14

N-[6,9-dihydro-9-[[2-hydroxy-1-(hydroxymethyl)ethoxy]methyl]-6-oxo-1H-purin-2-yl]acetamide

616-148-00-X

424-550-1

84245-12-5

Tar oils, brown-coal; Light Oil; [The distillate from lignite tar boiling in the range of approximately 80 °C to 250 °C (176 °F to 482 °F). Composed primarily of aliphatic and aromatic hydrocarbons and monobasic phenols.]

648-002-00-6

302-674-4

94114-40-6

J

Benzol forerunnings (coal); Light Oil Redistillate, low boiling; [The distillate from coke oven light oil having an approximate distillation range below 100 °C (212 °F). Composed primarily of C₄ to C₆ aliphatic hydrocarbons.]

648-003-00-1

266-023-5

65996-88-5

J

Distillates (coal tar), benzole fraction, BTX-rich; Light Oil Redistillate, low boiling; [A residue from the distillation of crude benzole to remove benzole fronts. Composed primarily of benzene, toluene and xylenes boiling in the range of approximately 75 °C to 200 °C (167 °F to 392 °F).]

648-004-00-7

309-984-9

101896-26-8

J

Aromatic hydrocarbons, C_6-10, C₈-rich; Light Oil Redistillate, low boiling

648-005-00-2

292-697-5

90989-41-6

J

Solvent naphtha (coal), light; Light Oil Redistillate, low boiling

648-006-00-8

287-498-5

85536-17-0

J

Solvent naphtha (coal), xylene-styrene cut; Light Oil Redistillate, intermediate boiling

648-007-00-3

287-502-5

85536-20-5

J

Solvent naphtha (coal), coumarone-styrene contg.; Light Oil Redistillate, intermediate boiling

648-008-00-9

287-500-4

85536-19-2

J

Naphtha (coal), distn. residues; Light Oil Redistillate, high boiling; [The residue remaining from the distillation of recovered naphtha. Composed primarily of naphthalene and condensation products of indene and styrene.]

648-009-00-4

292-636-2

90641-12-6

J

Aromatic hydrocarbons, C₈; Light Oil Redistillate, high boiling

648-010-00-X

292-694-9

90989-38-1

J

Aromatic hydrocarbons, C_8-9, hydrocarbon resin polymn. by-product; Light Oil Redistillate, high boiling; [A complex combination of hydrocarbons obtained from the evaporation of solvent under vacuum from polymerized hydrocarbon resin. It consists predominantly of aromatic hydrocarbons having carbon numbers predominantly in the range of C₈ through C₉ and boiling in the range of approximately 120 °C to 215 °C (248 °F to 419 °F).]

648-012-00-0

295-281-1

91995-20-9

J

Aromatic hydrocarbons, C_9-12, benzene distn.; Light Oil Redistillate, high boiling

648-013-00-6

295-551-9

92062-36-7

J

Extract residues (coal), benzole fraction alk., acid ext.; Light Oil Extract Residues, low boiling; [The redistillate from the distillate, freed of tar acids and tar bases, from bituminous coal high temperature tar boiling in the approximate range of 90 °C to 160 °C (194 °F to 320 °F). It consists predominantly of benzene, toluene and xylenes.]

648-014-00-1

295-323-9

91995-61-8

J

Extract residues (coal tar), benzole fraction alk., acid ext.; Light Oil Extract Residues, low boiling; [A complex combination of hydrocarbons obtained by the redistillation of the distillate of high temperature coal tar (tar acid and tar base free). It consists predominantly of unsubstituted and substituted mononuclear aromatic hydrocarbons boiling in the range of 85 °C to 195 °C (185 °F to 383 °F).]

648-015-00-7

309-868-8

101316-63-6

J

Extract residues (coal), benzole fraction acid; Light Oil Extract Residues, low boiling; [An acid sludge by-product of the sulfuric acid refining of crude high temperature coal. Composed primarily of sulfuric acid and organic compounds.]

648-016-00-2

298-725-2

93821-38-6

J

Extract residues (coal), light oil alk., distn. overheads; Light Oil Extract Residues, low boiling; [The first fraction from the distillation of aromatic hydrocarbons, coumarone, naphthalene and indene rich prefractionator bottoms or washed carbolic oil boiling substantially below 145 °C (293 °F). Composed primarily of C₇ and C₈ aliphatic and aromatic hydrocarbons.]

648-017-00-8

292-625-2

90641-02-4

J

Extract residues (coal), light oil alk., acid ext., indene fraction; Light Oil Extract Residues, intermediate boiling

648-018-00-3

309-867-2

101316-62-5

J

Extract residues (coal), light oil alk., indene naphtha fraction; Light Oil Extract Residues, high boiling; [The distillate from aromatic hydrocarbons, coumarone, naphthalene and indene rich prefractionator bottoms or washed carbolic oils, having an approximate boiling range of 155 °C to 180 °C (311 °F to 356 °F). Composed primarily of indene, indan and trimethylbenzenes.]

648-019-00-9

292-626-8

90641-03-5

J

Solvent naphtha (coal); [The distillate from either high temperature coal tar, coke oven light oil, or coal tar oil alkaline extract residue having an approximate distillation range of 130 °C to 210 °C (266 °F to 410 °F). Composed primarily of indene and other polycyclic ring systems containing a single aromatic ring. May contain phenolic compounds and aromatic nitrogen bases.]; Light Oil Extract Residues, high boiling

648-020-00-4

266-013-0

65996-79-4

J

Distillates (coal tar), light oils, neutral fraction; Light Oil Extract Residues, high boiling; [A distillate from the fractional distillation of high temperature coal tar. Composed primarily of alkyl-substituted one ring aromatic hydrocarbons boiling in the range of approximately 135 °C to 210 °C (275 °F to 410 °F). May also include unsaturated hydrocarbons such as indene and coumarone.]

648-021-00-X

309-971-8

101794-90-5

J

Distillates (coal tar), light oils, acid exts.; Light Oil Extract Residues, high boiling; [This oil is a complex mixture of aromatic hydrocarbons, primarily indene, naphthalene, coumarone, phenol, and o-, m- and p-cresol and boiling in the range of 140 °C to 215 °C (284 °F to 419 °F).]

648-022-00-5

292-609-5

90640-87-2

J

Distillates (coal tar), light oils; Carbolic Oil; [A complex combination of hydrocarbons obtained by distillation of coal tar. It consists of aromatic and other hydrocarbons, phenolic compounds and aromatic nitrogen compounds and distills at the approximate range of 150 °C to 210 °C (302 °F to 410 °F).]

648-023-00-0

283-483-2

84650-03-3

J

Tar oils, coal; Carbolic Oil; [The distillate from high temperature coal tar having an approximate distillation range of 130 °C to 250 °C (266 °F to 410 °F). Composed primarily of naphthalene, alkylnaphthalenes, phenolic compounds, and aromatic nitrogen bases.]

648-024-00-6

266-016-7

65996-82-9

J

Extract residues (coal), light oil alk., acid ext.; Carbolic Oil Extract Residue; [The oil resulting from the acid washing of alkali-washed carbolic oil to remove the minor amounts of basic compounds (tar bases). Composed primarily of indene, indan and alkylbenzenes.]

648-026-00-7

292-624-7

90641-01-3

J

Extract residues (coal), tar oil alk.; Carbolic Oil Extract Residue; [The residue obtained from coal tar oil by an alkaline wash such as aqueous sodium hydroxide after the removal of crude coal tar acids. Composed primarily of naphthalenes and aromatic nitrogen bases.]

648-027-00-2

266-021-4

65996-87-4

J

Extract oils (coal), light oil; Acid Extract; [The aqueous extract produced by an acidic wash of alkali-washed carbolic oil. Composed primarily of acid salts of various aromatic nitrogen bases including pyridine, quinoline and their alkyl derivatives.]

648-028-00-8

292-622-6

90640-99-6

J

Pyridine, alkyl derivs.; Crude Tar Bases; [The complex combination of polyalkylated pyridines derived from coal tar distillation or as high-boiling distillates approximately above 150 °C (302 °F) from the reaction of ammonia with acetaldehyde, formaldehyde or paraformaldehyde.]

648-029-00-3

269-929-9

68391-11-7

J

Tar bases, coal, picoline fraction; Distillate Bases; [Pyridine bases boiling in the range of approximately 125 °C to 160 °C (257 °F to 320 °F) obtained by distillation of neutralized acid extract of the base-containing tar fraction obtained by the distillation of bituminous coal tars. Composed chiefly of lutidines and picolines.]

648-030-00-9

295-548-2

92062-33-4

J

Tar bases, coal, lutidine fraction; Distillate Bases

648-031-00-4

293-766-2

91082-52-9

J

Extract oils (coal), tar base, collidine fraction; Distillate Bases; [The extract produced by the acidic extraction of bases from crude coal tar aromatic oils, neutralization, and distillation of the bases. Composed primarily of collidines, aniline, toluidines, lutidines, xylidines.]

648-032-00-X

273-077-3

68937-63-3

J

Tar bases, coal, collidine fraction; Distillate Bases; [The distillation fraction boiling in the range of approximately 181 °C to 186 °C (356 °F to 367 °F) from the crude bases obtained from the neutralized, acid-extracted base-containing tar fractions obtained by the distillation of bituminous coal tar. It contains chiefly aniline and collidines.]

648-033-00-5

295-543-5

92062-28-7

J

Tar bases, coal, aniline fraction; Distillate Bases; [The distillation fraction boiling in the range of approximately 180 °C to 200 °C (356 °F to 392 °F) from the crude bases obtained by dephenolating and debasing the carbolated oil from the distillation of coal tar. It contains chiefly aniline, collidines, lutidines and toluidines.]

648-034-00-0

295-541-4

92062-27-6

J

Tar bases, coal, toluidine fraction; Distillate Bases

648-035-00-6

293-767-8

91082-53-0

J

Distillates (petroleum), alkene-alkyne manuf. pyrolysis oil, mixed with high-temp. coal tar, indene fraction; Redistillates; [A complex combination of hydrocarbons obtained as a redistillate from the fractional distillation of bituminous coal high temperature tar and residual oils that are obtained by the pyrolytic production of alkenes and alkynes from petroleum products or natural gas. It consists predominantly of indene and boils in a range of approximately 160 °C to 190 °C (320 °F to 374 °F).]

648-036-00-1

295-292-1

91995-31-2

J

Distillates (coal), coal tar-residual pyrolysis oils, naphthalene oils; Redistillates; [The redistillate obtained from the fractional distillation of bituminous coal high temperature tar and pyrolysis residual oils and boiling in the range of approximately 190 °C to 270 °C (374 °F to 518 °F). Composed primarily of substituted dinuclear aromatics.]

648-037-00-7

295-295-8

91995-35-6

J

Extract oils (coal), coal tar-residual pyrolysis oils, naphthalene oil, redistillate; Redistillates; [The redistillate from the fractional distillation of dephenolated and debased methylnaphthalene oil obtained from bituminous coal high temperature tar and pyrolysis residual oils boiling in the approximate range of 220 °C to 230 °C (428 °F to 446 °F). It consists predominantly of unsubstituted and substituted dinuclear aromatic hydrocarbons.]

648-038-00-2

295-329-1

91995-66-3

J

Extract oils (coal), coal tar-residual pyrolysis oils, naphthalene oils; Redistillates; [A neutral oil obtained by debasing and dephenolating the oil obtained from the distillation of high temperature tar and pyrolysis residual oils which has a boiling range of 225 °C to 255 °C (437 °F to 491 °F). Composed primarily of substituted dinuclear aromatic hydrocarbons.]

648-039-00-8

310-170-0

122070-79-5

J

Extract oils (coal), coal tar residual pyrolysis oils, naphthalene oil, distn. residues; Redistillates; [Residue from the distillation of dephenolated and debased methylnaphthalene oil (from bituminous coal tar and pyrolysis residual oils) with a boiling range of 240 °C to 260 °C (464 °F to 500 °F). Composed primarily of substituted dinuclear aromatic and heterocyclic hydrocarbons.]

648-040-00-3

310-171-6

122070-80-8

J

Distillates (coal), coke-oven light oil, naphthalene cut; Naphthalene Oil; [The complex combination of hydrocarbons obtained from prefractionation (continuous distillation) of coke oven light oil. It consists predominantly of naphthalene, coumarone and indene and boils above 148 °C (298 °F).]

648-084-00-3

285-076-5

85029-51-2

J, M

Distillates (coal tar), naphthalene oils; Naphthalene Oil; [A complex combination of hydrocarbons obtained by the distillation of coal tar. It consists primarily of aromatic and other hydrocarbons, phenolic compounds and aromatic nitrogen compounds and distills in the approximate range of 200 °C to 250 °C (392 °F to 482 °F).]

648-085-00-9

283-484-8

84650-04-4

J, M

Distillates (coal tar), naphthalene oils, naphthalene-low; Naphthalene Oil Redistillate; [A complex combination of hydrocarbons obtained by crystallization of naphthalene oil.Composed primarily of naphthalene, alkyl naphthalenes and phenolic compounds.]

648-086-00-4

284-898-1

84989-09-3

J, M

Distillates (coal tar), naphthalene oil crystn. mother liquor; Naphthalene Oil Redistillate; [A complex combination of organic compounds obtained as a filtrate from the crystallization of the naphthalene fraction from coal tar and boiling in the range of approximately 200 °C to 230 °C (392 °F to 446 °F). Contains chiefly naphthalene, thionaphthene and alkylnaphthalenes.]

648-087-00-X

295-310-8

91995-49-2

J, M

Extract residues (coal), naphthalene oil, alk.; Naphthalene Oil Extract Residue; [A complex combination of hydrocarbons obtained from the alkali washing of naphthalene oil to remove phenolic compounds (tar acids). It is composed of naphthalene and alkyl naphthalenes.]

648-088-00-5

310-166-9

121620-47-1

J, M

Extract residues (coal), naphthalene oil, alk., naphthalene-low; Naphthalene Oil Extract Residue; [A complex combination of hydrocarbons remaining after the removal of naphthalene from alkali-washed naphthalene oil by a crystallization process. It is composed primarily of naphthalene and alkyl naphthalenes.]

648-089-00-0

310-167-4

121620-48-2

J, M

Distillates (coal tar), naphthalene oils, naphthalene-free, alk. exts.; Naphthalene Oil Extract Residue; [The oil remaining after the removal of phenolic compounds (tar acids) from drained naphthalene oil by an alkali wash. Composed primarily of naphthalene and alkyl naphthalenes.]

648-090-00-6

292-612-1

90640-90-7

J, M

Extract residues (coal), naphthalene oil alk., distn. overheads; Naphthalene Oil Extract Residue; [The distillate from alkali-washed naphthalene oil having an approximate distillation range of 180 °C to 220 °C (356 °F to 428 °F). Composed primarily of naphthalene, alkylbenzenes, indene and indan.]

648-091-00-1

292-627-3

90641-04-6

J, M

Distillates (coal tar), naphthalene oils, methylnaphthalene fraction; Methylnaphthalene Oil; [A distillate from the fractional distillation of high temperature coal tar. Composed primarily of substituted two ring aromatic hydrocarbons and aromatic nitrogen bases boiling in the range of approximately 225 °C to 255 °C (437 °F to 491 °F).]

648-092-00-7

309-985-4

101896-27-9

J, M

Distillates (coal tar), naphthalene oils, indole-methylnaphthalene fraction; Methylnaphthalene Oil; [A distillate from the fractional distillation of high temperature coal tar. Composed primarily of indole and methylnaphthalene boiling in the range of approximately 235 °C to 255 °C (455 °F to 491 °F).]

648-093-00-2

309-972-3

101794-91-6

J, M

Substances

Index No

EC No

CAS No

Notes

Carbon monoxide

006-001-00-2

211-128-3

630-08-0

Lead hexafluorosilicate

009-014-00-1

247-278-1

25808-74-6

▼M14

Slimes and sludges, copper electrolyte refining, decopperised

028-015-00-8

305-433-1

94551-87-8

Silicic acid, lead nickel salt

028-050-00-9

—

68130-19-8

▼C1

Lead compounds with the exception of those specified elsewhere in this Annex

082-001-00-6

A ►M5, E ◄

Lead alkyls

082-002-00-1

A ►M5, E ◄

Lead azide

082-003-00-7

236-542-1

13424-46-9

Lead chromate

082-004-00-2

231-846-0

7758-97-6

Lead di(acetate)

082-005-00-8

206-104-4

301-04-2

Trilead bis(orthophosphate)

082-006-00-3

231-205-5

7446-27-7

Lead acetate

082-007-00-9

215-630-3

1335-32-6

Lead(II) methanesulphonate

082-008-00-4

401-750-5

17570-76-2

C.I. Pigment Yellow 34; (This substance is identified in the Colour Index by Colour Index Constitution No C.I. 77603.)

082-009-00-X

215-693-7

1344-37-2

C.I. Pigment Red 104; (This substance is identified in the Colour Index by Colour Index Constitution No C.I. 77605.)

082-010-00-5

235-759-9

12656-85-8

Lead hydrogen arsenate

082-011-00-0

232-064-2

7784-40-9

1,2-Dibromo-3-chloropropane

602-021-00-6

202-479-3

96-12-8

2-bromopropane

602-085-00-5

200-855-1

75-26-3

►M5 E ◄

Warfarin; 4-hydroxy-3-(3-oxo-1-phenylbutyl)coumarin

607-056-00-0

201-377-6

81-81-2

Lead 2,4,6-trinitroresorcinoxide, lead styphnate

609-019-00-4

239-290-0

15245-44-0

Substances

Index No

EC No

CAS No

Notes

▼M14

Dibutyltin hydrogen borate

005-006-00-7

401-040-5

75113-37-0

Boric acid; [1]

005-007-00-2

233-139-2 [1]

10043-35-3 [1]

Boric acid, crude natural, containing not more than 85 % of H₃BO₃ calculated on the dry weight; [2]

234-343-4 [2]

11113-50-1 [2]

Diboron trioxide; Boric oxide

005-008-00-8

215-125-8

1303-86-2

Disodium tetraborate, anhydrous;

005-011-00-4

Boric acid, disodium salt; [1]

215-540-4 [1]

1330-43-4 [1]

Tetraboron disodium heptaoxide, hydrate; [2]

235-541-3 [2]

12267-73-1 [2]

Orthoboric acid, sodium salt; [3]

237-560-2 [3]

13840-56-7 [3]

Disodium tetraborate decahydrate; Borax decahydrate

005-011-01-1

215-540-4

1303-96-4

Disodium tetraborate pentahydrate; Borax pentahydrate

005-011-02-9

215-540-4

12179-04-3

Sodium perborate; [1]

005-017-00-7

239-172-9 [1]

15120-21-5 [1]

Sodium peroxometaborate; [2]

231-556-4 [2]

7632-04-4 [2]

Sodium peroxoborate; [containing < 0,1 % (w/w) of particles with an aerodynamic diameter of below 50 μm]

Sodium perborate; [1]

005-017-01-4

239-172-9 [1]

15120-21-5 [1]

Sodium peroxometaborate; [2]

231-556-4 [2]

7632-04-4 [2]

Sodium peroxoborate; [containing ≥ 0,1 % (w/w) of particles with an aerodynamic diameter of below 50 μm]

Perboric acid (H₃BO₂(O₂)), monosodium salt trihydrate; [1]

005-018-00-2

239-172-9 [1]

13517-20-9 [1]

Perboric acid, sodium salt, tetrahydrate; [2]

234-390-0 [2]

37244-98-7 [2]

Perboric acid (HBO(O₂)), sodium salt, tetrahydrate; [3]

231-556-4 [3]

10486-00-7 [3]

Sodium peroxoborate hexahydrate; [containing < 0,1 % (w/w) of particles with an aerodynamic diameter of below 50 μm]

Perboric acid (H₃BO₂(O₂)), monosodium salt, trihydrate; [1]

005-018-01-X

239-172-9 [1]

13517-20-9 [1]

Perboric acid, sodium salt, tetrahydrate; [2]

234-390-0 [2]

37244-98-7 [2]

Perboric acid (HBO(O₂)), sodium salt, tetrahydrate; [3]

231-556-4 [3]

10486-00-7 [3]

Sodium peroxoborate hexahydrate; [containing ≥ 0,1 % (w/w) of particles with an aerodynamic diameter of below 50 μm]

Perboric acid, sodium salt; [1]

005-019-00-8

234-390-0 [1]

11138-47-9 [1]

Perboric acid, sodium salt, monohydrate; [2]

234-390-0 [2]

12040-72-1 [2]

Perboric acid (H₃BO₂(O₂)), monosodium salt, monohydrate; [3]

231-556-4 [3]

10332-33-9 [3]

Sodium peroxoborate; [containing < 0,1 % (w/w) of particles with an aerodynamic diameter of below 50 μm]

Perboric acid, sodium salt; [1]

005-019-01-5

234-390-0 [1]

11138-47-9 [1]

Perboric acid, sodium salt, monohydrate; [2]

234-390-0 [2]

12040-72-1 [2]

Perboric acid (H₃BO₂(O₂)), monosodium salt, monohydrate; [3]

231-556-4 [3]

10332-33-9 [3]

Sodium peroxoborate; [containing ≥ 0,1 % (w/w) of particles with an aerodynamic diameter of below 50 μm]

▼C1

Linuron (ISO) 3-(3,4-dichlorophenyl)-1-methoxy-1-methylurea

006-021-00-1

206-356-5

330-55-2

►M5 E ◄

6-(2-Chloroethyl)-6(2-methoxyethoxy)-2,5,7,10-tetraoxa-6-silaundecane; etacelasil

014-014-00-X

253-704-7

37894-46-5

Flusilazole (ISO); bis(4-fluorophenyl)-(methyl)-(1H-1,2,4-triazol-1-ylmethyl)-silane

014-017-00-6

—

85509-19-9

►M5 E ◄

A mixture of: 4-[[bis-(4-fluorophenyl)-methylsilyl]methyl]-4H-1,2,4-triazole; 1-[[bis-(4-fluorophenyl)methyl-silyl]methyl]-1H-1,2,4-triazole

014-019-00-7

403-250-2

—

►M5 E ◄

▼M14

(4-ethoxyphenyl)(3-(4-fluoro-3-phenoxyphenyl)propyl)dimethylsilane

014-036-00-X

405-020-7

105024-66-6

Tris(2-chloroethyl)phosphate

015-102-00-0

204-118-5

115-96-8

Glufosinate ammonium (ISO); Ammonium 2-amino-4-(hydroxymethylphosphinyl)butyrate

015-155-00-X

278-636-5

77182-82-2

▼C1

Potassium dichromate

024-002-00-6

231-906-6

7778-50-9

►M5 E ◄

Ammonium dichromate

024-003-00-1

232-143-1

7789-09-5

►M5 E ◄

▼M14

Sodium dichromate

024-004-00-7

234-190-3

10588-01-9

▼M14 —————

▼C1

Sodium chromate

024-018-00-3

231-889-5

7775-11-3

►M5 E ◄

▼M14

Cobalt dichloride

027-004-00-5

231-589-4

7646-79-9

Cobalt sulfate

027-005-00-0

233-334-2

10124-43-3

Cobalt acetate

027-006-00-6

200-755-8

71-48-7

Cobalt nitrate

027-009-00-2

233-402-1

10141-05-6

Cobalt carbonate

027-010-00-8

208-169-4

513-79-1

▼C1

Nickel tetracarbonyl

028-001-00-1

236-669-2

13463-39-3

▼M14

Nickel dihydroxide; [1]

028-008-00-X

235-008-5 [1]

12054-48-7 [1]

Nickel hydroxide; [2]

234-348-1 [2]

11113-74-9 [2]

Nickel sulfate

028-009-00-5

232-104-9

7786-81-4

Nickel carbonate;

028-010-00-0

Basic nickel carbonate;

Carbonic acid, nickel (2+) salt; [1]

222-068-2 [1]

3333-67-3 [1]

Carbonic acid, nickel salt; [2]

240-408-8 [2]

16337-84-1 [2]

[μ-[carbonato(2-)-O:O′]]dihydroxy trinickel; [3]

265-748-4 [3]

65405-96-1 [3]

[carbonato(2-)]tetrahydroxytrinickel; [4]

235-715-9 [4]

12607-70-4 [4]

Nickel dichloride

028-011-00-6

231-743-0

7718-54-9

Nickel dinitrate; [1]

028-012-00-1

236-068-5 [1]

13138-45-9 [1]

Nitric acid, nickel salt; [2]

238-076-4 [2]

14216-75-2 [2]

Slimes and sludges, copper electrolytic refining, decopperised, nickel sulfate

028-014-00-2

295-859-3

92129-57-2

Nickel diperchlorate; Perchloric acid, nickel (II) salt

028-016-00-3

237-124-1

13637-71-3

Nickel dipotassium bis(sulfate); [1]

028-017-00-9

237-563-9 [1]

13842-46-1 [1]

Diammonium nickel bis(sulfate); [2]

239-793-2 [2]

15699-18-0 [2]

Nickel bis(sulfamidate); Nickel sulfamate

028-018-00-4

237-396-1

13770-89-3

Nickel bis(tetrafluoroborate)

028-019-00-X

238-753-4

14708-14-6

Nickel diformate; [1]

028-021-00-0

222-101-0 [1]

3349-06-2 [1]

Formic acid, nickel salt; [2]

239-946-6 [2]

15843-02-4 [2]

Formic acid, copper nickel salt; [3]

268-755-0 [3]

68134-59-8 [3]

Nickel di(acetate); [1]

028-022-00-6

206-761-7 [1]

373-02-4 [1]

Nickel acetate; [2]

239-086-1 [2]

14998-37-9 [2]

Nickel dibenzoate

028-024-00-7

209-046-8

553-71-9

Nickel bis(4-cyclohexylbutyrate)

028-025-00-2

223-463-2

3906-55-6

Nickel (II) stearate; Nickel (II) octadecanoate

028-026-00-8

218-744-1

2223-95-2

Nickel dilactate

028-027-00-3

—

16039-61-5

Nickel (II) octanoate

028-028-00-9

225-656-7

4995-91-9

Nickel difluoride; [1]

028-029-00-4

233-071-3 [1]

10028-18-9 [1]

Nickel dibromide; [2]

236-665-0 [2]

13462-88-9 [2]

Nickel diiodide; [3]

236-666-6 [3]

13462-90-3 [3]

Nickel potassium fluoride; [4]

- [4]

11132-10-8 [4]

Nickel hexafluorosilicate

028-030-00-X

247-430-7

26043-11-8

Nickel selenate

028-031-00-5

239-125-2

15060-62-5

Nickel dithiocyanate

028-046-00-7

237-205-1

13689-92-4

Nickel dichromate

028-047-00-2

239-646-5

15586-38-6

Nickel dichlorate; [1]

028-053-00-5

267-897-0 [1]

67952-43-6 [1]

Nickel dibromate; [2]

238-596-1 [2]

14550-87-9 [2]

Ethyl hydrogen sulfate, nickel (II) salt; [3]

275-897-7 [3]

71720-48-4 [3]

Nickel (II) trifluoroacetate; [1]

028-054-00-0

240-235-8 [1]

16083-14-0 [1]

CAS No

Index No

EC No

Substances

1.

92-67-1

612-072-00-6

202-177-1

biphenyl-4-ylamine 4-aminobiphenyl xenylamine

2.

92-87-5

612-042-00-2

202-199-1

benzidine

3.

95-69-2

202-441-6

4-chloro-o-toluidine

4.

91-59-8

612-022-00-3

202-080-4

2-naphthylamine

5.

97-56-3

611-006-00-3

202-591-2

o-aminoazotoluene 4-amino-2',3-dimethylazobenzene 4-o-tolylazo-o-toluidine

6.

99-55-8

202-765-8

5-nitro-o-toluidine

7.

106-47-8

612-137-00-9

203-401-0

4-chloroaniline

8.

615-05-4

210-406-1

4-methoxy-m-phenylenediamine

9.

101-77-9

612-051-00-1

202-974-4

4,4'-methylenedianiline 4,4'-diaminodiphenylmethane

10.

91-94-1

612-068-00-4

202-109-0

3,3'-dichlorobenzidine 3,3'-dichlorobiphenyl-4,4'-ylenediamine

11.

119-90-4

612-036-00-X

204-355-4

3,3'-dimethoxybenzidine o-dianisidine

12.

119-93-7

612-041-00-7

204-358-0

3,3'-dimethylbenzidine 4,4'-bi-o-toluidine

13.

838-88-0

612-085-00-7

212-658-8

4,4'-methylenedi-o-toluidine

14.

120-71-8

204-419-1

6-methoxy-m-toluidine p-cresidine

15.

101-14-4

612-078-00-9

202-918-9

4,4'-methylene-bis-(2-chloro-aniline) 2,2'-dichloro-4,4'-methylene-dianiline

16.

101-80-4

202-977-0

4,4'-oxydianiline

17.

139-65-1

205-370-9

4,4'-thiodianiline

18.

95-53-4

612-091-00-X

202-429-0

o-toluidine 2-aminotoluene

19.

95-80-7

612-099-00-3

202-453-1

4-methyl-m-phenylenediamine

20.

137-17-7

205-282-0

2,4,5-trimethylaniline

21.

90-04-0

612-035-00-4

201-963-1

o-anisidine 2-methoxyaniline

22.

60-09-3

611-008-00-4

200-453-6

4-amino azobenzene

CAS No

Index No

EC No

Substances

1.

Not allocated Component 1: CAS-No: 118685-33-9 C₃₉H₂₃ClCrN₇O₁₂S.2Na Component 2: C₄₆H₃₀CrN₁₀O₂₀S₂.3Na

611-070-00-2

405-665-4

A mixture of: disodium (6-(4-anisidino)-3-sulfonato-2-(3,5-dinitro-2-oxidophenylazo)-1-naphtholato)(1-(5-chloro-2-oxidophenylazo)-2-naphtholato)chromate(1-); trisodium bis(6-(4-anisidino)-3-sulfonato-2-(3,5-dinitro-2-oxidophenylazo)-1-naphtholato)chromate(1-)

European standardisation organisation (¹)

Reference and title of the standard

Reference document

Reference of the superseded standard

CEN

Leather — Chemical tests — Determination of certain azocolorants in dyed leathers

CEN ISO/TS 17234:2003

NONE

CEN

Textiles — Methods for the determination of certain aromatic amines derived from azocolorants — Part 1: Detection of the use of certain azo colorants accessible without extraction

EN 14362-1:2003

NONE

CEN

Textiles — Methods for determination of certain aromatic amines derived from azocolorants — Part 2: Detection of the use of certain azo colorants accessible by extracting the fibres

EN 14362-2:2003

NONE

(¹) ESO: European standardisation organisations: ►M5 CEN: Avenue Marnix 17, 1000 Brussels, Belgium, tel. +32 2550 08 11, fax +32 2550 08 19 (http://www.cen.eu/cenorm/homepage.htm) Cenelec: Avenue Marnix 17, B-1000 Brussels, tel. +32 25196871, fax +32 2519 69 19 (http://www.cenelec.eu/Cenelec/Homepage.htm) ◄ ETSI: 650, route des Lucioles, F-06921 Sophia Antipolis; tel. (33) 492 94 42 00, fax (33) 493 65 47 16. http://www.etsi.org

Substances

Derogations

1. (a) Sodium perborate; perboric acid, sodium salt; perboric acid, sodium salt, monohydrate; sodium peroxometaborate; perboric acid (HBO(O₂)), sodium salt, monohydrate; sodium peroxoborate CAS No 15120-21-5; 11138-47-9; 12040-72-1; 7632-04-4; 10332-33-9 EC No 239-172-9; 234-390-0; 231-556-4 (b) Perboric acid (H₃BO₂(O₂)), monosodium salt trihydrate; perboric acid, sodium salt, tetrahydrate; perboric acid (HBO(O₂)), sodium salt, tetrahydrate; sodium peroxoborate hexahydrate CAS No 13517-20-9; 37244-98-7; 10486-00-7 EC No 239-172-9; 234-390-0; 231-556-4

Detergents as defined by Regulation (EC) No 648/2004 of the European Parliament and of the Council (¹). The derogation shall apply until 1 June 2013.

(¹) OJ L 104, 8.4.2004, p. 1.