Directive 2013/53/EU Article 20: Design and construction

Article 20 - Design and construction

‹

Article 20

Design and construction

›

1. With regard to design and construction of recreational craft the following procedures set out in Annex II to Decision No 768/2008/EC shall apply:

((a))

For design categories A and B referred to in point 1 of Part A of Annex I:(i)For recreational craft of hull length from 2,5 m to less than 12 m, any of the following modules:—Module A1 (internal production control plus supervised product testing);—Module B (EU type-examination) together with Module C, D, E or F;—Module G (conformity based on unit verification);—Module H (conformity based on full quality assurance).(ii)For recreational craft of hull length from 12 m to 24 m, any of the following modules:—Module B (EU type-examination) together with Module C, D, E or F;—Module G (conformity based on unit verification);—Module H (conformity based on full quality assurance).

((i))

For recreational craft of hull length from 2,5 m to less than 12 m, any of the following modules:—Module A1 (internal production control plus supervised product testing);—Module B (EU type-examination) together with Module C, D, E or F;—Module G (conformity based on unit verification);—Module H (conformity based on full quality assurance).

((ii))

For recreational craft of hull length from 12 m to 24 m, any of the following modules:—Module B (EU type-examination) together with Module C, D, E or F;—Module G (conformity based on unit verification);—Module H (conformity based on full quality assurance).

((b))

For design category C referred to in point 1 of Part A of Annex I:(i)For recreational craft of hull length from 2,5 m to less than 12 m, any of the following modules:—where the harmonised standards relating to points 3.2 and 3.3 of Part A of Annex I are complied with: Module A (internal production control), Module A1 (internal production control plus supervised product testing), Module B (EU type-examination) together with Module C, D, E or F, Module G (conformity based on unit verification) or Module H (conformity based on full quality assurance);—where the harmonised standards relating to points 3.2 and 3.3 of Part A of Annex I are not complied with: Module A1 (internal production control plus supervised product testing), Module B (EU type-examination) together with Module C, D, E or F, Module G (conformity based on unit verification) or Module H (conformity based on full quality assurance);(ii)For recreational craft of hull length from 12 m to 24 m, any of the following modules:—Module B (EU type-examination) together with Module C, D, E or F;—Module G (conformity based on unit verification);—Module H (conformity based on full quality assurance).

((i))

For recreational craft of hull length from 2,5 m to less than 12 m, any of the following modules:—where the harmonised standards relating to points 3.2 and 3.3 of Part A of Annex I are complied with: Module A (internal production control), Module A1 (internal production control plus supervised product testing), Module B (EU type-examination) together with Module C, D, E or F, Module G (conformity based on unit verification) or Module H (conformity based on full quality assurance);—where the harmonised standards relating to points 3.2 and 3.3 of Part A of Annex I are not complied with: Module A1 (internal production control plus supervised product testing), Module B (EU type-examination) together with Module C, D, E or F, Module G (conformity based on unit verification) or Module H (conformity based on full quality assurance);

((ii))

((c))

For design category D referred to in point 1 of Part A of Annex I:for recreational craft of hull length from 2,5 m to 24 m, any of the following modules:—Module A (internal production control);—Module A1 (internal production control plus supervised product testing);—Module B (EU type-examination) together with Module C, D, E or F;—Module G (conformity based on unit verification);—Module H (conformity based on full quality assurance).

—	Module A1 (internal production control plus supervised product testing);

—	Module B (EU type-examination) together with Module C, D, E or F;

—	Module G (conformity based on unit verification);

—	Module H (conformity based on full quality assurance).

—	Module B (EU type-examination) together with Module C, D, E or F;

—	Module G (conformity based on unit verification);

—	Module H (conformity based on full quality assurance).

—

where the harmonised standards relating to points 3.2 and 3.3 of Part A of Annex I are complied with: Module A (internal production control), Module A1 (internal production control plus supervised product testing), Module B (EU type-examination) together with Module C, D, E or F, Module G (conformity based on unit verification) or Module H (conformity based on full quality assurance);

—

where the harmonised standards relating to points 3.2 and 3.3 of Part A of Annex I are not complied with: Module A1 (internal production control plus supervised product testing), Module B (EU type-examination) together with Module C, D, E or F, Module G (conformity based on unit verification) or Module H (conformity based on full quality assurance);

—	Module B (EU type-examination) together with Module C, D, E or F;

—	Module G (conformity based on unit verification);

—	Module H (conformity based on full quality assurance).

—	Module A (internal production control);

—	Module A1 (internal production control plus supervised product testing);

—	Module B (EU type-examination) together with Module C, D, E or F;

—	Module G (conformity based on unit verification);

—	Module H (conformity based on full quality assurance).

2. With regard to design and construction of personal watercraft any of the following procedures set out in Annex II to Decision No 768/2008/EC shall apply:

((a))

Module A (internal production control);

((b))

Module A1 (internal production control plus supervised product testing);

((c))

Module B (EU type-examination) together with Module C, D, E or F;

((d))

Module G (conformity based on unit verification);

((e))

Module H (conformity based on full quality assurance).

3. With regard to design and construction of components any of the following procedures set out in Annex II to Decision No 768/2008/EC shall apply:

((a))

Module B (EU type-examination) together with Module C, D, E or F;

((b))

Module G (conformity based on unit verification);

((c))

Module H (conformity based on full quality assurance).

Metadata

✓ In force

↻ Amendments (1)

17/01/2014 current
28/12/2013 first version in the database